Healey Posted January 12, 2018 Share Posted January 12, 2018 My car was running perfectly with the stock turbo and the afr’s we’re good. Then I put the td04 on and it idles fine around 14.7 and it also fuels fine when not on boost but as soon as these is any boost it just leans right out. Installed a rrfpr today but that didn’t help either Quote Link to post Share on other sites
5e colin Posted January 12, 2018 Share Posted January 12, 2018 (edited) how lean ??? you wont see the rich afrs till like 4500rpm or s0 what afr at what rmp at what boost dont expect much afr under 0.5bar i remember when i ran like that then very quikly drops to 10.8 to 11.2 ot there abouts stock ecu ?? or p&p stock ecu and injectors are fine at just under Fc Edited January 12, 2018 by 5e colin Quote Link to post Share on other sites
Healey Posted January 12, 2018 Author Share Posted January 12, 2018 Like 15 - 16, just bought a map sensor to see if that’s the problem Quote Link to post Share on other sites
Healey Posted January 12, 2018 Author Share Posted January 12, 2018 6 minutes ago, 5e colin said: how lean ??? stock ecu ?? or p&p Like 15 - 16, just bought a map sensor to see if that’s the problem and it’s on stock ecu with a 0.4 bar spring Quote Link to post Share on other sites
5e colin Posted January 12, 2018 Share Posted January 12, 2018 at what rpm are you seeing that and in what gear dont be expecting to see mad afr on 0.4 bar good indeed to check the map sensor voltage reading to see if its sending correct voltage map could be fine working for ecu but still be out without seeing an eml Quote Link to post Share on other sites
Healey Posted January 12, 2018 Author Share Posted January 12, 2018 7 minutes ago, 5e colin said: at what rpm are you seeing that and in what gear dont be expecting to see mad afr on 0.4 bar good indeed to check the map sensor voltage reading to see if its sending correct voltage map could be fine working for ecu but still be out without seeing an eml I’m seeing it in every gear at high and low revs Quote Link to post Share on other sites
00joeindastarb0 Posted January 12, 2018 Share Posted January 12, 2018 Whats the rrfpr set at? Quote Link to post Share on other sites
Healey Posted January 12, 2018 Author Share Posted January 12, 2018 1 minute ago, 00joeindastarb0 said: Whats the rrfpr set at? I set it at stock pressure and it was lean so I tried it at 3 bar and it was richer at idle but still lean as soon as any boost was present Quote Link to post Share on other sites
5e colin Posted January 12, 2018 Share Posted January 12, 2018 only do your runs in 3rd dont worry about the other gears if you nail 3rd al will be fine just refit the stockk fpr mate untill you get this sorted Quote Link to post Share on other sites
Healey Posted January 12, 2018 Author Share Posted January 12, 2018 15 minutes ago, 5e colin said: only do your runs in 3rd dont worry about the other gears if you nail 3rd al will be fine just refit the stockk fpr mate untill you get this sorted Okay so if I fit the stock fpr on again, I was seeing 13.5 afr ok boost in 3rd, isn’t that still too lean? Quote Link to post Share on other sites
5e colin Posted January 12, 2018 Share Posted January 12, 2018 (edited) 2 hours ago, Healey said: I’m seeing it in every gear at high and low revs you need to be way more specific mate 13.5 will be to 4000rpm ( low boost ) almost tdo4 wont be on full boost past 4500 rpm expect 11.5 / 11.9 what gauge have you ( afr ) Edited January 12, 2018 by 5e colin Quote Link to post Share on other sites
Healey Posted January 12, 2018 Author Share Posted January 12, 2018 2 hours ago, 5e colin said: you need to be way more specific mate 13.5 will be to 4000rpm ( low boost ) almost tdo4 wont be on full boost past 4500 rpm expect 11.5 / 11.9 what gauge have you ( afr ) I didn’t really go through the Rev range too much, bit worried about it being too lean, I’ll have another drive tomorrow with the stock regulator and it’s an AEM wideband Quote Link to post Share on other sites
5e colin Posted January 13, 2018 Share Posted January 13, 2018 (edited) Just remember your only on 0.4 bar not much extra feuling is needed unrill its spooling propperly Reach 11 s between 4 and 5 try fitting @ . 8 bbar spring might be better for feuling as most run just under fc with h no issue like u have Edited January 13, 2018 by 5e colin Quote Link to post Share on other sites
Healey Posted January 13, 2018 Author Share Posted January 13, 2018 11 minutes ago, 5e colin said: Just remember your only on 0.4 bar not much extra feuling is needed unrill its spooling propperly Reach 11 s between 4 and 5 try fitting @ . 8 bbar spring might be better for feuling as most run just under fc with h no issue like u have Okay cheers I’ll try that later, I took off the FPR and fuelling was much better Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.