nano

hi, still available?

Thanks is it possible to get the ring , i have the disc with no.ring and no abs.

Hello, Who has ever mounted a speed sensor to the rear of a Starlet? What type of sensors to choose and where it should be mounted? Is it a quite easy operation? This is for setting launch control based on rpm and ground speed. Thanks

Alright mate thanks a lot

Thanks rob. Could you specify a model please, single, double clutch?

H

Hi, i installed greddy ultimate piggyback with boomslang harness about a year ago, it was ok. My oem ecu loom was a mess so i decided to make a more tidy one. The problem is now the car wont start. It smells fuel. Remove the emu. Oem ecu plugged only. Car runs fine. I think the emu is faulty. Is it possible To use emu without using ignition input output if i just loop them? Thanks

Hi the hose to bov is ok. Very easy to see if there is a leak there. Thanks

Hi everybody, I was driving my car on full boost ,0.8bar. Suddenly i heard like bang, car lost power and wont boost over 0.2bar.Car is running good under boost though, no smoke no rattle etc... I checked ic piping, all good. Dump valve is ok too. The wastegate is a genuine tial f38 i bought 6 years ago. Can a bad diaphragm cause boost leak or on the contrary i should overboost as the valve wont open. I m confused because my friend says a bad Diaphragm can cause boost leak. Can it be the turbo itself? I say again no whislte no smoke at exhaust.

Ok sorted. Injectors harness is not good. I used my 2ee one and injectors are all together and in a 4efte they re seperate

Hi, my car is running really bad atm. It starts well. But idle is rich(Black plugs) and 10afr on brand new aem wideband and cant accelerate smoothly. In one Word its undrivable. My attention is on the map sensor. I get 1.7v on idle with multimètre on pim line when its idling and 2.66v ignition on engine off Shouldnt it be around 0.2v when idling ? Can someone confirm this please. If so, mean map sensor needs to be replaced?

Thanks. One more question : i ve distributor ox and knock loom all together and its added to the main loom. They are all shield and they end in a Orange connector where ground wires but they are cut. Can i ground the shielding on the châssis ? What happens if the shielding arent grounded? Is it something to worry about or no importance ?thanks

Hi I m adding o2 distributor and knock sensor loom for a gt conversion. All the shieldings go To a connector with brown wires but they are cut. Must i connect thoses Hi I m adding o2 distributor and knock sensor loom for a gt conversion. All the shieldings go To a connector with brown wires but they are cut. Must i connect one brown wire to the main loom? Can i leave it like that? What causes not to earth them? Thanks

Ok sorted 60amp yellow fuse was dead. I think this is for alternator.

New problem now : battery light stays on when car is running. Turn off the key, turn on again and no power at all. Efi fuse keeps blowing up :(((

Thanks mate the 15a efi fuse was broken. I. checked the wrong one first.

Hi i ve a problem with my car, glanza engine swapped in a ep81. The car was running well. Now , when i turn key on i ve no light on dash and no starter. Only warning lights, horn, High lights. Could you guys help me ? Where should i source the issue? Thanks

Hi everyone, I bought a tial mvs wastegate. There are 2 black springs in it. One large and one small. The large one is supposed to be 0.8bar but what about the small one? Tial website does not mention it. Actually i want to know how much pressure there is in it with the 2 springs combined. Tanks

Hi, as above, anyone has this for sale and ready to ship it to reunion postcode 97470. Thanks By the way looking for the rear lip as well. Thanks

any help?

i dont know mate. when i look at the diagram blue et ultimate seem , power is the same... thanks for reply

hi everyone, my friend has a 4efe with turbo and greddy emanage blue. he s just upgraded to the ultimate. he uses the same harness (custom) fot the ultimate. the problem is that the ultimate stays on with key off. when he put the blue back on, its ok. what can cause this please? thanks

hi, I'm after a front lip bumper first gen. will the 98 lip fit it ? please pm me if you have this for sale, cheers

as above, who has this can ship to me. location: reunion

hi , what is the best tyre/wheel to put athe the back for drag race. I have 22.08.13 slick at the front. thanks