Anderj26

Well after a long day/night it runs! I remembered about the service bolt 😊 Fired up straight away which i was delighted about! Wasn't so delighted with the sump gushing oil everywhere so whipped it off and cleaned it up and sealed it. Everything now good leak wise. I get a weird noise now and again but its from the plate between the gearbox and engine. If i bolt it up it makes the most horrendous noise ever! If i leave it unbolted it makes the noise every now and then. The fan was hooked up to a switch on the dash. Beside the mirror switch. I replaced the 30a fan fuse. Reconnected the wires and the fan runs constantly unless i unplug the temp sensor on the thermostat ( very front one) any ideas on how to fix? I will go do a search and then tinker about tomorrow with it 😊 Thanks everyone for your help over the last few days! Very appreciated! Thanks James

Yeah leads are on the right way. Checked ignition timing and everything good! Cleaned all connections just to be safe. Whipped of the rocker cover and the inlet cam hasn't been lined up properly when the previous owner did the head gasket. Hopefully after i redo them the can will have the proper compression and fire 😊 fingers crossed! Thanks all for he help and i will let you know if it fires 😊 Thanks James

Ok thanks everyone. So my timing will be bang on then as ive already set it to 0 and the notch in the cam cap. I will double check the ignition side and get the timing light onto it. Thanks everyone i will let you know tomorrow how it goes. James

Ahhh so the bottom has to be at 0 not at 10? Sorry i was confused there and was going to time the bottom crankshaft to 10 and the camshaft to the notch in the head. If the timing has to be at the notch and at 0 on the crank the. I have a strange problem. The car is popping through the exhaust and the inlet indicating the timing is wrong however it is set up to the spec your saying. Sure it is the crankshaft pulley to 0?

Could you please explain more about this 2 dots to 1? I have timed the camshaft pulley up to the 4e hole to the little indent in the cap. Roughly a little bit right of 12oclock position? Is this correct? Thanks James

Ok thanks guys. Read so many places that said 0 and then others that said 10 degrees. Other ones told me to set it up to the oil pump mark and the notch. So thanks for clearing that up. That will explain the no compression and popping through the exhaust. I have used an earthing kit and used my battery drill and a wire wheel to make sure everyone had a good earth. Cleaned up all existing earths, even the ones in the footwell just to be on the safe side! Unfortunately got to go to the girlfriends parents tomorrow for a sunday lunch so wont be able to get to my garage till monday. First thing i will do is set it for 10degrees! Thanks everyone for helping and i will let you know how i get on on monday. Thanks James

I have checked the pipes on the throttle body and everything ok. I keep rechecking the timing as when its cranking over its popping through the exhaust. Do i time it up to 10 or the 0? The 4e hole is lined up with the notch but every time i try to time it up to 10degrees it is always a tooth out. Just home for my dinner so will keep trying after! Thanks

I will get to the bottom of it eventually! Haha I have tried that and it just constantly flashes. So no codes as far as i can tell. Im going to start swapping bits and bobs that i have spare just to rule stuff out 😊! Besides that I'm stumped! I will let you know if anything cures it 😊

After triple checking i am 100% sure it isn't the wrong way round. But if anyone has a good diagram or a good explanation of where each pipe should go i will check again tomorrow Thanks James

Replaced my engine in my ep91. Also fitted a ramhorm manifold and external wastegate ect! Now when i bought the car the engine was already removed so had to finish of someone elses handywork! Needless to say its in and i think everything is where it should be. I primed the turbo and there apears to be no leaks. Filled with coolant and had a small leak on the inlet manifold, so filled the water jacket with sealant as i guess this is just for ep82 models? No leaks now! Now when i got the engine the belt had been replaced and the timing was already set. I double checked and it was a tooth out so lined everything back up and timed it to the 0mark on the crankshaft. Is this correct or should it be 10? So i went to fire it up and theres just no bite or anything! As if it doesnt want to go and i can hear popping through the exhaust. I am getting spark on all 4 cylinders and apears to be a good spark! I am getting plenty of fuel pressure as it keeps flooding. So in theory it should go bang. But its not. I have tried a different ecu just to see but still nothing. I have took the plugs out and hope the fuel will evaporate for me to go back and check tomorrow. Any help will be very apreciated as im starting to pull my hair out slightly! Thanks James

Needing a decat asap! Pm me with what you have 😊! Thanks James

Thankfully i have found someone about 20 minutes away that has rebuilt a fresh ep82 4efte so im away to collect that at 10 and hopefully have it in and running tonight. Its had a new oil pump, New belt Water pump Head gasket and gasket set So saves me alot of hassle and means i can forge my spare lump on the side! So if anyone has pistons and rods for sale then give me a shout 😊 Thanks

Hello, My 4efte roasted a rod and bearings because oil pump is goosed! Ive removed the crank and it looks to far gone to me. Severely scored! Cylinder 1 conrod bent and piston knackered! My question is that i have a complete 4efe which was running before i took the engine out. Can i remove the crank out of the 4efe and use it in the 4efte? I know the pistons are different in the n/a but i have spare turbo pistons and rods. So could just get the crank checked over, polished, new bearings and bolt up the 4efte pistons and rods? Thanks in advance 😊!

My 4efte roasted a piston and crank so Looking for a 4efte complete good condition block. Or a bare running engine Located in Moray Scotland So would need posted if out of driving distance! Cheers

I think because i asked for the engine first i should get dibs 😝!

If you wanted to sell the engine separate and sell the Gearbox to mikey i would be interested in doing a deal for it posted. Thanks

Reflex silver side skirts added

Dials sold!

Ttt

Yeah i paid £10 for a hpi check on my car checker just to be sure and it says it was an import! Surely no one would import a N/a and then convert it to a turbo would they? I am hoping they have had a wing mirror knocked off and just put a set of n/a ones on Wishful thinking Thanks James

Morning I didn't know they made a lower spec V. Well I'm buying it as spares or repairs, Needs a head gasket apparently. Always wanted one in white as i have a black ep82 and a red n/A at my garage But i have a few spare engines lying so mechanically it wouldn't be a problem to change out ect. I just was a bit concerned about value. If it was a conversion it wouldn't be worth as much as a genuine V when i buy it or when i come to re-sell later on down the line? Maybe im just being daft but wanted a few opinions? Thanks for such a quick reply James

New bits added

Hello everyone Buying a new project tonight.... Does anyone recognize it? Im a little worried as it could be a conversion! I will have a look at the vin plate tonight and see! Just wanted to know if anyone has seen or know anything about the car Thanks James

Anyone happen to have a set lying around? Would need them posted to Elgin Scotland Thanks James

Item For Sale: Glanza side skirts in Reflex silver Item Condition & Description: Sideskirts are ok, Few scrapes and stone chips. Nothing too major! Price: £100 posted? Picture Item For Sale: 4EFTE full Engine loom, ECU , Fuse box and Headlight loom ! Item Condition & Description: Good condition throughout! Looks slightly untidy as has been in the box since i bought it. Was run with Emanage blue previously! Price:£175 Posted? Pictures: Payment & Shipping Details: Can be locally picked up from Elgin, Scotland! Item For Sale: 4EFE Complete engine and gearbox ( will split if required) Item Condition & Description: Was removed from a T reg N/a with 65000 miles. Engine was running spot on before removal. No whines or knocks from gearbox! Price:£250 for the lot? Pictures: Payment & Shipping Details:Could be palleted and sent if required but depends on location for price! Item For Sale: Inlet manifold for 4efte complete with throttle position sensors ect! Item Condition & Description:Good condition, Could do with a good clean with the power washer! will do this before it will be sent! Price:£80 Posted? Pictures: Payment & Shipping Details:Can be posted anywhere or Local pick up from Elgin Scotland! Item For Sale: N/A pair of wing mirrors Item Condition & Description:Good condition in black. Manual adjusting. Price:£30 Pictures: Payment & Shipping Details:£10 posted in uk, or local pick up from Elgin Moray Item For Sale:4efte Cams Item Condition & Description: I have inspected them, and there is no scores ect. some corrosion on faces due to lying around for so long! Will clean up but wanted to show them the way they are so didn't clean them up to show them truthfully! Price:£30 Pictures: Payment & Shipping Details:Postage depending on location ect or local pick up from Elgin Scotland Item For Sale: 4efte pistons and rods Item Condition & Description: Good condition Pistons, slight marks on face and carboned up. but will clean up fine! Price:offers as don't know what they are worth :/ Pictures: Payment & Shipping Details:will post anywhere or local pick up from Elgin Scotland Item For Sale:2 sets of 4efte Buckets and shims Item Condition & Description: All are in good condition, no scores or that! Price: pm me best offer as have no clue what these are worth Pictures: Payment & Shipping Details: Will post anywhere or local pick up Open to offers on all items. As wasn't too sure what everything was worth! So prices are pure Guess's! I have a heap more bits so will try and get pictures of them today and get them up! Thanks for looking James