glanza ep91 23

I'm going tdo4 which cancels the oem cat so where could I buy a 400 cel cat to weld into the mid section of my exhaust thanks

Ok thanks

I mean the an size of the male fitting encircle

What is the an size of the oem fuel pressure regulator

I plan to swap my oem fuel rail to the zisco an10 fuel rail and do I have to swap this part of the oem rail over to the zisco one or can I just leave it out

Thanks very much

It's looking that way I'll definitely get a professional to build the head I just want to find out who's the best around and what I have to look out for (a lot of idiots around who think they know it all I just want to know what I'm on about so I don't get fooled) thanks for all your help

What about standered but higher lift

Basically I want the works, I plan to fully forge the engine (8:1 comp)and plan on running a Garrett gt28 , not sure on ecu yet The head seems to be a black art so I want to get the best for the car Thanks

I have a 5e which I'll be forging and I also want to build the head aswell And I'm not sure what high lift cams to get

Thanks

What are the Mazda rx7 turbo 550cc injectors part numbers

Hi I hadnt updated this project thread in a while i tinted the back window because the old tint was old faded and cracked I then took off the red wheel nuts because a few of them had cracked! So I got some Toyota ones Wetvac the cars seats carpets boot Then the battery went and I replaced that and after that the starter went so I got a reconditioned one from Toyota and I got it fit Then I striped the interior to fix the leak in the book and to check the wiring I found the odd few twist and tape jobs so i sent it to an autoelectriction and I got him to put in the indigo dials and his turbo timer Then I flushed the engine and change the oil and use Toyota filter Sprayed the some off the interior plastic to gunmetal grey Coilovers arrived and my autobahn88 finally arrived after a month wait for the fmic and I got them fitted Pic of standard engine bay before Bcs set up properly for handling I also got some evo 4 Recaroseats aswell and I put I a new pioneer radio because the Old one broke I'm after purchasing te37 alloys and I got them powdercoated by sodablast in black with sparkle clear coat Sodablasted Powdercoted i got a stage 3 spec clutch and tdo4 braided water and oil line. a walbro fuel pump I also sprayed the rocker cover wrinkle red I installed a triple core half rad and roose motersport hoses I also bought a apexi black edition boost controller I removed the air conditioning pipes rad and compresser I also installed a new roter arm and blue magncore leads and I gave it a service.i replace the long route intercooler piping with a short route pipe then I purchase c pillar strut brace and a oem optional extra rear strut brace and I also purchased a 98 spec glanza steering wheel just need know the bolt sizes for the rear struts Got Idworkz lips oem style front and rear and car will be going in to respray very soon

What is the toyota part number for the plug I can't find it using the diagrams

What is the toyota part number for the plug I can't find it using the diagrams

It's a emange ultimate

Need some advice here I want to get fairly large injectors it is currently a tdo4 with standered fuel rail (will be forging and bigger turbo eventually) anyone have any suggestions for a drop in 550+cc injectors that doesn't need resistors thanks

I need contact email for midland turbo I tried the email on there website and it didn't work thanks very much

Cork

Hello all , my names john I'm 16 and from cork Ireland , A few months ago I bought a 96 glanza turbo that was freshly rebuilt by Bart in the JDM garage in cork . I have serious plans for the car as I never plan on selling it . I want it to be an absolute sleeper. So far I bought a blitz nur spec cat-back exhaust , a td04 turbo and decat off one of my brothers friends and a greddy ultimate ecu a 3 bar map sensor and bc coilovers I plan to td04 it properly in the summer once I have other supporting mods purchased (injectors , fmic , clutch ) This will be a slow thread as I'm a student and money is tight as I don't work many hours .

Hi lads new to the site I'm from Ireland and I have a glanza