Bug679

Didn't fancy tackling that as there's a big difference from top to bottom on the lip but reckon it's the only way. Anyway I'll throw up a few pics tomorrow after work and see from there. Thanks again man 👍🏻

Ya it's screwed to I wondered what the big spacers where I'll get a pic up tomorrow might have to cut the lip and stick it back on 🙈🤕

Thanks man

It was hanging off it sort of but dopey balls here stuck it on and didn't notice till I had it bonded on so it stuck now lol. Is there a difference with 98 and 96 fitment ? I tried it on my 96 and seemed to be OK was tight putting it on that's why I just stuck it to the one it came on

Picked up a rear lip and bumper and the lip is sticking past the bumper about a 1/4 inch each side that meant to be ? 😕 Or a copy lip with bad fitment any pics would be useful can't find any am looking on the Google

Thanks

If I was you pat I would use bullet connectors so you can disconnect it and plug the loom wires back together that's the way am doing my EMB so male connector on EMB loom and whatever female to male on loom to match so it can be plugged in as I'd say you have to cut some wires to intercept the signal to ECU to run through dastek. Hope that makes sense

This is the connectors am using

https://www.ebay.ie/itm/400776800196

House of kolor be your best bet mate here's a couple of blues of theirs

http://house-of-kolor.co.uk/index.php?main_page=product_info&products_id=512

http://house-of-kolor.co.uk/index.php?main_page=product_info&products_id=511

Fixed it. Took the plastic cover off and one of the teeth snapped off and was stuck inbetween them stopping it locking. Happy days 👍🏻

is there a replays from yesterdays topgear ?? mist it

Bbc2 11:20 tonight

Lol it's just gonna have to be operated on then lol 🤕😷 cheers for the input man 👍🏻

The passenger seat works perfect just takes about 3 clicks after tilting drivers back to lock in position 😬

It's not the sliders that the problem they work perfectly it's for tilting the seat back and forward is the problem see the pic ( not the best but ya can see it tilts to far back in stock position ) don't like been a cruiser lol need to be upright 🙃

Cheers for the replies guys

You using a breaker bar ? Can be your best friend removing bolts and nuts 😝

Pete_a is yours in Gt or Glanza ? Just asking because if they still in original car it must be something on the adjuster then 🤔 So could be common enough wait and see if anymore replies could get it sussed 😀😀 or tear it apart and have a gander lol

So got these fitted today no cutting or that just drilled two holes for the pins to fit in taught it was handier than cutting them off but the drivers seat only locks back in position when it's about 3 clicks back from been straight and is a bit to far back for my liking is there a known problem with the adjuster on them ? Thanks for any help

Have a Greddy bcc there same job as the jam

Where you down in Donegal lad ? Could of swore I seen the car in pic going through Castleblayney on the Monday after 🤔

Just what am after . Thanks man 👍🏻

I know it's there but if anyone can link the thread gets a big 😘 Just looking to see what's involved thanks as am collecting a pair tomorrow 🙃

What was the problem ? Might help someone else out in the future 🤔

Nice car man 👍🏻 as you said good base to start with best of luck with it

Get a 35mm lanking cap for intercooler pipe and flutter the itch out. sorry have no _ utton anymore. ya any pics of your car man and welcome along hope you have a last

That definitely don't look good at all man

pair of good pipe grips pulls them right off

Lol that's about the height of it 😂😂

Have you got any advice for sorting the crack along the top out? Mines the same and I'm not sure how I'll go about repairing it haha

The way I went about it was clamping it together and stuffing fibreglass inside the lip and mould it inside the upper curve where the crack is to strengthen it up again and fibreglass fillers on outside sand it down when dry takes about half hour to harden depending how you mix it then ordinary fillers sand smooth , primer then stopper any wee holes primer again sand. It's honestly not that hard just fiddly getting the fibreglass inside and moulded use a good bit of resin give it some more strength. Hope that makes sense 👍🏻