cam13T

Hi, i have a cusco master cylinder stopper and am wondering if i have the correct one. I have a glanza with ABS, and am trying to fit Pic-1, it just doesnt seem to line up- i havent had a good go at it yet but i thought it would be easier. I have done a bit of searching and i know there are 2 models, so does anybody know if Pic-1 fits on the glanza with abs? or do i need pic-2. PIC-1 PIC-2

I thought so, Thanks Idrees

I have a set of the late model glanza clear taillight lenses and i have some taillight units from a ep95. They will bolt up fine but as the only difference between them is that the late model ones are clear. So wont the top brake light wont be red except for the little red strip. Do the late model lights have some internal differences like a red cover inside??

How do i save my sent messages? edit- Just found the box when writing a message that says 'send copy to sent items'

Yes they should come off easily, there should be a little dab of glue at each end and then peel them off slowly. I would recommend getting new ones and they are not exspensive (In Aus they were $50ea = 25GBPea.) They are nice and shiny makes the roof look brand-new and are alot easier to fit then the old and they come with the double sided tape attached too.

Can anyone with a glanza help me?

Hi, i am building a glanza from a n/a and i have swapped the rear axel over to rear discs etc. I need to know where or what direction these 6 wires head in? They travel from the ABS unit under the steering-wheel and down under the drivers side sill cover and head towards the rear. My loom was cut half-way as i got a front-cut. I believe the twisted pairs go to the sensors on each side but unsure where the others should be correctly terminated. The abs plugs enter the floor pan in front of the rear wheels and on the vertical part infront of the rear seats. So does anyone have there glanza strip

Yes i 2nd that, Manifold and dump and new actuator should be on top of the list.

any body here that has one of these, could you tell me where the 2 wires go to. Thanks

Hi, i have a illuminated surround for the ignition barrel from a glanza and i am wondering which wires i connect it too.

Yes from memory it is tucked in the passenger side of the bootlid, Wiper Control- Blue box.

Yes definately try a live feed to the motor, i had a similar problem a few months ago with a crook motor. Take off door trim get a bit of 2-core twin cable jam that on your battery and test it directly on the motor.

I was told it was the same as this mate.

all sorted now i found a diagram. Thanks

Does anyone know how to wire up a Jam FCD to a glanza V. I have four wires coming off the fcd- Red-white-Black-green. Thanks

Ok good, i have just installed slotted discs and braided lines i have the abs now also. Is the Master cylinder stopper a good mod/needed for street driving?

thanks

Hi, whats involved in fitting an electic a/c panel climate control to a car with the standard a/c panel.

Can someone with a glanza please tell me how the rear wires for the ABS are run, and what colours go to each side. Thanks

Hi there i recently purchased a HKS Actuator and was wondering if someone could tell me if this method is correct to install to keep using the Glanza Dash Hi/Lo button. In the kit comes with a little brass piece that reduces the diameter to 2.5mm, it looks like i install that in the P8 100mm hose and then connect to the T-piece. I know this is the pic for ep82 but it should be similar but just with different hose lengths for the ep91. So is this correct do i insert the little brass reducer here?? Thanks

Hi there, im just in the process of ordering a oil catch can and apparently there are 2 sizes of inlets a 9mm and a 15mm. I cant get to my engine now so can someone please tell me if i need the big or small inlets. Thanks.

Yes i got a blitz harness too, on the small 3-pin plug you are pointing to 1 wire (purple) goes to the handbrake, and the other orange and white i didn't use. Just tap into the handbrake cable in the grey plug under the ashtray section im pretty sure its (Yellow/red stripe.) So when the handbrake is realeased during a countdown it will automatically shut the engine off.

Mate your best off getting one with a harness made for your model so it is plug and play, makes installing easy as and if you want to remove it for some reason you dont have split wires.

yes i should have the correct ones next week. yes the shape is the same nothing special but hey i dont sit in the back!

All sorted, i was talking about the bottom part of the rear seat where the ep91 is bolted. I did find out that it is possible to put them in though, apparently you need the clip/latch from the ep82 body and there is a hole for them on the ep91 which is blanked.