-
Content Count
171 -
Joined
-
Last visited
Content Type
Profiles
Forums
Wiki
Media Demo
Store
Calendar
Everything posted by ep91_glanza
-
can someone help???
-
i took the vaccum pipe off the actuator and it is now wanting to boost loads so could it be a dodgy actuator or?????cheers
-
ive checked everything nd thats the only thing that it might be,but even if i alter the boost would i not see a change ? Cheers
-
i think the hotpipe that goes on the turbo is leaking but i didnt think that would lose so much boost would it??
-
Ive just fitted my engine andBefore it was set at 1.0 bar but now it wont go past .5 bar ive tried turning boost up but dosnt make any difference.can any of yous help??? Cheers karl
-
I looked at the torque specs on tgtt and it said 1st 22nm 2nd 44nm the 3rd had 90o is that degree turn or 90 nm thanks for help in advance
-
Ive just fitted a new engine and wondering if i need it setup on a rolling road again?
-
Just ive done an engine rebuild and got a bee r rev limiter and didnt know if i wanted to take a chance
-
Hi i just want some opinions on the rev limiters and if they are safe to use if used only on the strip?? Anyone using them at the minute??Cheers karl
-
Ive done a bearing does that mean that ive got to get a different size bearing or what?? Help much appriciatado!!! Lol
-
i recently had a loud knocking noise coming from my engine so i took the engine out and basically took it all apart and found out that i span one of my conrod bearings and it totally worn the bearing down and has worn the little lip/groove on the crank shaft where the conrod bearing sits and there is signs of wear on the conrod, im just wondering if i just replace the bearings or what i need some advice cheers.if pics would be easier i can get them up tmrw
-
Very impressed with the delivery and service off enzo it was only a pcv valve but no matter what it is hes got it or can get it to ya within a few days....cheers matey.karl
-
Glanza¥¥¥
ep91_glanza replied to ep91_glanza's topic in EP91 Glanza Progress Blogs
got some pics of the wheels -
Glanza¥¥¥
ep91_glanza replied to ep91_glanza's topic in EP91 Glanza Progress Blogs
Hi does anyone wanna do a swap for some rota rewinds with no kerb marks a little sign of etching on the chrome and has four new tyres 15z -
i think it is just normal gear oil because it hasnt got the viscosity on the bottle its just honda mtf for manual transmission
-
i think this is normal colour but can get it cheap because nearly all me mates have hondas haha
-
yeah mate cheers for the help just pm me a price or text/ring. Karl 07837014409 cheers
-
yeah if you can mate its the seal on the gearbox where the driveshafts go in
-
Hi just a little help please i need a gearbox seal does any one know where to get them on the internet and how much or do i need to go to toyota for them cheers
-
Silver glanza spotted newcastle
ep91_glanza replied to ep91_glanza's topic in I Spy, Have You Been Spotted?
Im in a white whelans van because im busy rebuilding my gear box,clutch went and took it apart and happend to find that it ate away at the box too lol so will meet ya when back on the road matey -
Has anyone used honda mtf oil in their gearbox? Cheers karl
-
Silver glanza spotted newcastle
ep91_glanza replied to ep91_glanza's topic in I Spy, Have You Been Spotted?
Yeah mate it was u i was in the van ive seen u a few times sounds very nice as u passed. U aint got a dump valve have ya? -
Nice silver glanza near metro radio arena was this si's old one ??
-
Im in the middle of Putting my gearbox on and debating whether i should put landrover mtf oil in, ive heard that it is one of the best oils. has anyone got it or know of putting it in??? Cheers for help
-
welcome matey i see your from north east glad to see more starlets up this way. enjoy