K24_glanza
Member-
Content Count
212 -
Joined
-
Last visited
Content Type
Profiles
Forums
Wiki
Media Demo
Store
Calendar
Everything posted by K24_glanza
-
The exhaust is low but this isnt a daily drive so should be fine for the track and I will be staying clear of any speed bumps.
-
Boxing is supposed to be a sport
-
Having snags with the fuel pump running or not at the moment but should get it sorted soon. My plan was to get it looking like a glanza but due to the fact I am skint I am going to go for the sleeper look for now and focus on getting it running. Thanks for all your comments.
-
Contact Enzo on here if you still want an ep95
-
Finnaly got a few pics of my Forged K24 ep95 I ve been at this a while due to work commitments, being raped for cash by solicitors and Being ripped off for by a garage that done some work on my Bimmer but almost there now. What I have done so far: Fitted Fully forged 4e Blitz kkk K24 With custon screamer Poly bushed engine mounts fitted anti lift kit and poly bushed the front wish bone mounts. Fitted WMS 4 pots with yellow stuff pads, keeping the drums on the rear. I fitted D2's all round and got a friend to do some work to the rears but its still sitting quite high at the rear. I boug
-
No it doesnt start with bridge left in. I think I could have more than one problem. I am a bit fed up with it at the moment but Going to have another go on monday and check the spark plugs are actualy sparking Then update this. Cheers for the help very much appreciated.
-
Done what you said and the pump runs fine then tried to start it with no results. So i took out the spark plugs and turned it over with the pins un bridged and the fuel pump runs for a short period straight after I turn the ignition back to position 2. I am totally confused. Any one got any ideas?
-
Cheers thanks.
-
In the process of an ep95 turbo conversion and my fuel pump wont run at all. Checked my wiring and it seems ok. Has anyone had a similar issue or have any ideas? Hopeing for something obvious or going to take the pump out and go through the plug with a multi meter. Cheers peter
-
It looks really shit. wrapped in just black would look better than fake carbon.
-
This is a truely amazing project. Thanks for the inspiration.
-
any body Help with loom and inlet mani please
K24_glanza replied to K24_glanza's topic in 4WD Starlet Knowledge Base
I was just being a retardo. almost all sorted now -
I am Half way through an ep95 convertion. fitting the engine loom at the moment a but got a few plugs with no homes to go to. I know iam missing a few sensors but not sure which ones. Can any body take some pictures and label the sensors. I know iam missing the map sensor and I have the part that the dizzy cap plugs into. Also a bit lost with the hoses for the inlet mani the same would be helpful. Cheers peter
-
ep95 Rear lower engine mount size different to 91?
K24_glanza replied to K24_glanza's topic in Chassis & Suspension
I used appoxy. Yee haa! should work. figers crossed -
ep95 Rear lower engine mount size different to 91?
K24_glanza replied to K24_glanza's topic in Chassis & Suspension
Thats not good. The old bush is in pieces. -
ep95 Rear lower engine mount size different to 91?
K24_glanza posted a topic in Chassis & Suspension
I have just cut out the engine mounts from my ep95 only to realise that the lower engine bracket doesnt fit my new power flex bush. The bracket is slightly to big for the poly bush and the metal bush is not long enough. Just wondering if they have sent me the wrong kit or do the 95 and 91 have different lower brackets? -
Taggys EP70 Boxy, Forged TD04, 5E-FTE
K24_glanza replied to Taggy's topic in EP70 & EP71 Progress Blogs
found this maybe some help http://www.ebay.co.uk/itm/Banded-Steels-Ma...9#ht_694wt_1139 -
Thats quite horrible. Poor guy
-
Last time I seen a thread as good as this it was your SR build. The car looks amazing. Hope you get it all sorted soon.
-
ep85/ep95 upgraded rear anti roll bar + lowring spring kit
K24_glanza replied to a topic in 4WD Starlet Knowledge Base
Count me in for the RARB -
who stocks seals for blitz ex. waste gate
K24_glanza replied to K24_glanza's topic in Intake, Turbo & Exhaust
anyone? -
I have a full blitz k24 kit and need new seals for the external waste gate any ideas where i can get them?