-
Content Count
753 -
Joined
-
Last visited
Content Type
Profiles
Forums
Wiki
Media Demo
Store
Calendar
Posts posted by 1990timeismoney
-
-
Hi All.
Looking to buy a ep82 engine/ecu loom.over time wires have deteriorated and connectors broken so looking for a full replacement if any members have one around.
Thank you
Luke
-
-
-
-
For sale: under seat storage tray
Item Condition: well used condition.
Price and price conditions:
£80 plus +£8 delivery charge.
Extra Info:
never had the runners for the tray so unfortunately these won't be available its just the tray on its own.
Pictures:
Contact Details pm.
Location:
Isle of wight
Delivery & Conditions of Delivery:
£8 delivery Royal mail -
-
Hi all
Looking to buy an 38mm external wastegate with spring to run 1 bar of boost fitted.
Thank you
Luke
-
Hi all
Looking to buy a complete rear drivers side brake caliper . Good and fully working condition.
Thanks
Luke
-
hi all.
Looking to buy seat belt for passengers side ep82.
Luke
-
Ignition light gumtree may still be available.
-
Hi all.
Currently looking for a drivers side headlamp as mine has cracked.anyone with one for sale would be much appreciated.
Luke
-
-
-
I'll be in to sounds good
-
Bump
-
9 hours ago, H_D said:
bare in mind the baffle plate is steel and the rocker cover is aluminum, as long as the baffle has been drilled out properly any competent welder can blob weld it back in for you, I don't like the idea of using screws/bolts as I worry the may start to loosen off after a while which can cause serious engine failure if they fall out
That's a good point.as above I started to drill and tap for holes to use fasteners like washer spring washer with some high strength stud loctite.i to worry about losing a screw but I hope it holds if not it's of to the welders.and rebuilders.
I appreciate your reply and advice.will update with pics once complete.
-
3 hours ago, H_D said:
I had my baffle welded back in
That's a good option thank u for the advice.
-
Ok that's great thank you for the advice I'll get it all cleaned up and look into getting it either bolted or tacked.
-
Thank you for the reply.ill go with your recommendation and I'll get it drilled and tapped and get some loctite
-
Hi guys had my rocker cover welded with AN- fittings at the time had the baffle removed to make sure it was all clean underneath.do you need the baffle re installed or will it be ok without it.
-
Hi thank you for they reply.will be running blitz ECU and a td04 or the TF035 turbo. intercooler fpr etc its currently running 1bar with the td04 on standard wastegate
-
Hi all.looking to buy a 38mm wastegate for my turbo setup.along with any advice on the correct spring to run 1bar.
Thanks luke
-
For sale:
zisco inlet manifold with thermal gasket and 5e throttle cable
Item Condition:
used condition
Price and price conditions:
£210 plus paypal fees
Extra Info:
used condition never got around to fitting myself but has been previously used.
Pictures:
https://ibb.co/k7EzLK
https://ibb.co/i2iyEe
Contact Details:
pm
Location:
isle of wight
Delivery & Conditions of Delivery:
£10 courier -
Cheers socks it worked this time.
Thank you
Help needed Running lean.
in Ignition & Fueling
Posted
Hi guys
Having a few running issues with my EP82
Seems to fuel fine when cold. And idle fine. But as soon as it gets warm it bogs down when tried to be driven.also a very flat spot when stepping on gas.
One think I've noticed is that when it's warm if I remove a vacuum line the car goes from running lean to running better afr.
If anyone's had similar troubles like this any help would be greatly appreciated.
Thank you
Luke