motion Posted February 3, 2014 Share Posted February 3, 2014 (edited) himaybe it could be intresting for some people to know how much clearance the different lower arm barswill afford for your exhaust pipe.i got fitted my zisco lower arm bar for measurement today and here are the results:clearance between the tagged Point under the gearbox 25mmalso 25mm under my exhaust pipe but this point differs if you got another exhaust Systemso the gearbox point is better to comparehere is a picture you can see the measure of the middle of the hole to the lowest Point of the bar 50mm thickness 12mmshow us the measure of your bar and help People buy the one they need unfortunately the zisco one has to much clearance for me because i have only a 2 inch exhaust pipe and it sits very high.so i am intrested in a swap by the way. Edited February 3, 2014 by motion Quote Link to post Share on other sites
AlancEP82 Posted February 3, 2014 Share Posted February 3, 2014 I made my own a while back one off the best ones I made so far Quote Link to post Share on other sites
motion Posted February 3, 2014 Author Share Posted February 3, 2014 Wow looks very nice!!! but not much helpful for me I would like to know the measures of a cusco lower arm bar and a jd tech. Quote Link to post Share on other sites
morgey Posted February 3, 2014 Share Posted February 3, 2014 I've a cusco one off my car I can measure tonight. Quote Link to post Share on other sites
motion Posted February 3, 2014 Author Share Posted February 3, 2014 I've a cusco one off my car I can measure tonight.great! Quote Link to post Share on other sites
maddox710 Posted February 3, 2014 Share Posted February 3, 2014 I need one to clear a 3" exhaust Quote Link to post Share on other sites
motion Posted February 3, 2014 Author Share Posted February 3, 2014 I need one to clear a 3" exhaustdamn!!!! 3"!? Quote Link to post Share on other sites
morgey Posted February 3, 2014 Share Posted February 3, 2014 My 2.5" cleared my cusco brace with ease. Makes me think I could have mounted my engine a bit lower... oh well too late now lol Quote Link to post Share on other sites
morgey Posted February 3, 2014 Share Posted February 3, 2014 Cusco brace. 55mm from bottom to hole center line. 13mm thick tubing.Please note the tape measure is missing the hook so add on 1mm Quote Link to post Share on other sites
motion Posted February 3, 2014 Author Share Posted February 3, 2014 cheers Quote Link to post Share on other sites
Amjad Posted February 4, 2014 Share Posted February 4, 2014 Has anyone running the 4-point lower brace from Ultra Racing, got measurements? Quote Link to post Share on other sites
Tercel-R Posted February 4, 2014 Share Posted February 4, 2014 Has anyone running the 4-point lower brace from Ultra Racing, got measurements? I don't have measurements, but it was quite low to the ground. I took it off because it was scraping horribly. My NA exhaust was also very close to it and would hit occasionally which would drive me nuts. Quote Link to post Share on other sites
Amjad Posted February 4, 2014 Share Posted February 4, 2014 Thanks for the reply! Any idea how it sits in comparison to how low a Whiteline 24mm FARB is?And is your car quite low or at a sensible height? Quote Link to post Share on other sites
Tercel-R Posted February 5, 2014 Share Posted February 5, 2014 Well that's a dirty 22mm Whiteline FARB if you can see it. Here's a picture of the car with the lowering springs. The 4pt bar would clip road kill. Any half-dead squirrels were fully dead after meeting the Ultra racing bar. Quote Link to post Share on other sites
Amjad Posted February 5, 2014 Share Posted February 5, 2014 Haha! Thanks for that! I'm gonna have to see what happens, not 100% on it now as my car is a tad lower and it might end up catching everywhere Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.