Chief Quimby Posted March 30, 2015 Share Posted March 30, 2015 Took the engine out, now run a 5efte, but the old engine is still running in a friends ca, as stock, no turbo.Only have some pictures. Quote Link to post Share on other sites
starletmadyo Posted March 31, 2015 Author Share Posted March 31, 2015 Can you post them? Quote Link to post Share on other sites
Chief Quimby Posted March 31, 2015 Share Posted March 31, 2015 Mapconverter Quote Link to post Share on other sites
ashley newbert Posted April 1, 2015 Share Posted April 1, 2015 I'll start the list but i've never done the conversion myself but i think you'll need the following parts from a 4EFTE;How does the 4efte housing fit onto the 4efe block??? - ECU- Oil filter housing- Sump- Exhaust manifold and turbo, decat and exhaust to suit- Injectors and fpr (can't remember if they're the same on the efe to the fte but i assume fte ones are bigger)- Some form of intercooler I'm not sure if the 4efe have a knock sensor but if not they would have the casting for one to be fitted. The fte ecu won't like it if there's no knock sensor signal. Bear in mind that the compression is higher too so don't run silly boost. There's probably loads more but one of the converted lads is better off telling you what else you need. Quote Link to post Share on other sites
starletmadyo Posted April 5, 2015 Author Share Posted April 5, 2015 Nice car mate where would u find a map converter? Quote Link to post Share on other sites
Chief Quimby Posted April 5, 2015 Share Posted April 5, 2015 Only place to buy, is at www.turbomotor.dk Quote Link to post Share on other sites
starletmadyo Posted April 5, 2015 Author Share Posted April 5, 2015 Postage expensive? Quote Link to post Share on other sites
Chief Quimby Posted April 5, 2015 Share Posted April 5, 2015 Cant be, very small box, but just email him about it. Quote Link to post Share on other sites
starletmadyo Posted April 5, 2015 Author Share Posted April 5, 2015 Whitch section is it in don't understand any of it lol cud I jus use a glanza map sensor Quote Link to post Share on other sites
Chief Quimby Posted April 5, 2015 Share Posted April 5, 2015 If you are turboing your 4efe, then just use your 4efe mapsensor. Mail salg@turbomotor.dk about shipping or info. http://www.turbomotor.dk/contents/da/d11.htmlscroll down to mapconv Quote Link to post Share on other sites
starletmadyo Posted April 5, 2015 Author Share Posted April 5, 2015 Thanks very much with help is it straight fiward to install Quote Link to post Share on other sites
Chief Quimby Posted April 5, 2015 Share Posted April 5, 2015 Very easy to install and tune Quote Link to post Share on other sites
stewwy_94 Posted July 21, 2015 Share Posted July 21, 2015 so will the na boost with just the map converter or do you need other software? Quote Link to post Share on other sites
5e colin Posted July 22, 2015 Share Posted July 22, 2015 ^^^ ofcourse it needs to be mapped with an emanage etc etc Quote Link to post Share on other sites
Chief Quimby Posted July 26, 2015 Share Posted July 26, 2015 (edited) No 5E colin, you can adjust it with just this mapconverter Edited July 26, 2015 by Chief Quimby Quote Link to post Share on other sites
5e colin Posted July 26, 2015 Share Posted July 26, 2015 how is it going to alter the boost curve of the ignition and also the injectors ??? pm me some more info because it has me baffled Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.