Jump to content

Vturbo

Member
 View Profile  See their activity

  • Content Count

    651

  • Joined

  • Last visited

 Content Type 

Everything posted by Vturbo

  1. Vturbo
    Ah are you local?
  2. Vturbo
    To be honest Phil I thought the same. The mappers are being quite funny
  3. Vturbo
    Yeah what setup? Apparently too big for 1.5 bar on td04
  4. Vturbo
    I don't think the spray pattern is too good either
  5. Vturbo
    Yeah I have been advised by the mapper to get some smaller CC. Not sure the piggyback likes them.PM me if you have anything guys
  6. Vturbo
    Anyone got any 430cc injectors? Running 540's but they're a bit big, anyone fancy a swap or have some for sale?
  7. Vturbo
    Anyone on here?
  8. Vturbo
    Got them tyres fitted and enjoyed the car for the first time properly. Booked back in for a map tweak on the 7th. All I need now is to find a half rad.
  9. Vturbo
    Right so tonight I changed the knock sensor. That issue sorted. Checked the valve clearances, also all good. And tensioned the inlet cam gears, I can assume that was the rattle. Everything seems okay. Had a trip to Hertford yesterday and Picked up an uprated actuator and some ns2r's from Charlie. So all I need now is a half rad. Then go back for a map tweak
  10. Vturbo
    I would assume they spliced into it, it was fine for 2000 miles before mapping, going to change the sensor and check continuity on the wire and see where I'm at
  11. Vturbo
    The mapper was saying it's definitely not knocking. And that it's coming from the head.
  12. Vturbo
    Okay. So I picked th car up today. It threw an EML on the dyno. And the mapper was hearing a rattle through the det cans. It's code 52 open or short circuit for knock sensor. Never had this issue Untill they installed the ecu, so am I right in saying either the sensor gave up, or the wiring was damaged during the ecu install. And would this be a likely cause of the noise? Pulling timing etc
  13. Vturbo
    I really hope so!
  14. Vturbo
    Not got the car back yet. Tbh I have not heard anything out of place
  15. Vturbo
    Okay well, the car made 240 @1.4 bar, the mapper said the the actuator is weak, also there is a noise coming from the top end so they had to hold back. apparently it sounds like det but it's not. Happens past 5500rpm. Going to strip the head ASAP..: in the meantime any ideas?
  16. Vturbo
    I have done some longens in that car, changed the seating position so it's allot more comfortable. Just the 21 hours of exhaust drone
  17. Vturbo
    Fuck me mate mission! Bet that was good fun. I'm just worried about the car breaking down haha
  18. Vturbo
    Thinking about taking the starlet to southern Spain. As I fancy a by of an adventure, anyone got any experience?
  19. Vturbo
    Made it to the mappers, just waiting on news!
  20. Vturbo
    Small update, all the oil leaks have been fixed, resealed the sump and gave it a good clean out. Also sorted the rocker cover leaks and done the two front wheel bearings. So all is good and ready for mapping on Tuesday. Debating also wether to drive the car to southern Spain in a couple of months!
  21. Vturbo
    Not really much to update. Had to postpone mapping till the 5th of April due to work commitments. Gives me a bit of time to sort my dodgy wheel bearing and a few oil leaks..mainly sump and rocker cover. But other than that the miles are going on, up to 1700 miles. Just can't wait to get the thing mapped!
  22. Vturbo
    Yeah it's performing well. Only running 0.8 on an fpr and standard management. the gorge was epic though. I'm only down here till tomorrow then driving back
  23. Vturbo
    Took a drive up to Bristol, few pics from cheddar gorge
  24. Vturbo
    Fitted an adjustable fpr today, set it just under 3 bar and getting good afrs, haven't been able to really out the boot in until now.Feels great at 0.7 bar....can't wait to get if mapped to 1.4-1.5
  25. Vturbo
    Sure it's about 2.8
×
×
  • Create New...