-
Content Count
249 -
Joined
-
Last visited
Content Type
Profiles
Forums
Wiki
Media Demo
Store
Calendar
Posts posted by Sportif 4efte
-
-
2 hours ago, RobSR said:
Have you got the Glanza coil and igniter too? If not you will need this.
They are both a distributed ignition system yes but they are very different.
Thanks mate
-
On Wednesday, October 03, 2018 at 10:57 PM, RobSR said:
Ok so with the way you have done it the below is what I’d do.
Firstly the 4efe runs a different kind of idle control valve.
Id day you have 2 options, don’t run one, or fit a 4efte one. I’d go with fitting the 4efte one - 12v to one side from the Efi relay and then run the other side to the ECU. (Con 1, Pin 10)
In regards to the second question, the 4efe runs a 4-wire lambda rather than a single wire lambda like the 4efte. One of the 4 wires is the ‘heater’ for the sensor.
Remove the 4efe 4 wire sensor, and fit a single wire 4efte one and run this to Con 2, Pin 6.
Hope that helps
I’ve got 6 wires going to the n/a distributor 4pin plug and 2 pin plug on the glanza ecu I’ve only got a 4 pin plug. So far I’ve chopped the old 2 plugs off and put the glanza distributor plug on(without it being connected to the circuit) not too sure which wire to connect to which pin n what happens with the remaining 2 wires from n/a loom
N/a 4 pin connector blue green yellow white/black
N/a 2pin connector black/white/black
Glanza 4pin connector blue green white red.
That was the other question he asked me to ask for...
-
I’ve chopped of the ecu plugs (engine&dash) of the n/a loom and chopped of the 3 glanza ecu plugs of the glanza engine harness and glanza dash loom now I’m using the 3 glanza ecu plugs and connecting the pins to the n/a engine and dash loom (matching the pins) I’ve managed to match up everything apart from 2 pins which are 1 and 15 from the n/a engine loom n not to sure to which glanza pin they go to.
N/a engine loom Pin 1 rotary solenoid close-cold idle speed control
N/a engine loom pin 15 heated oxygen sensor. -
6 hours ago, RobSR said:
What loom are you using?
a GT 4efte one?
a Glanza 4efte?
the original 4efe one with the fte bits spliced in? Let me know and ill advise what you need to do.
You cant easily plug a 3 - connector Glanza ECU into the 2 - connector 4efe loom if thats what you are trying to do.
Mate yes I'm splicing fte bits into the na loom..
-
A friend of mine is the middle of a 4efe to 4efe-t...the problem he has atm is... If any one can help...
Glanza ecu connector 1 pin 10 and 11 what do they connect to..
N/a starlet 16 pin connector pin 1 and 15.
Anyways around these..
Thanks guys.
-
Aquired engine and dash loom
-
On Mon Mar 26 2018 11:16:13 GMT+0100, lukEp said:
FYI The engine loom and fuse box are two separate looms mate.
Yes mate, I need all of the looms
-
Also require clean front bumper and bonnet depends what you guys got for sale..
-
Require a 96 glanza v manual engine loom (uncut) with fuse box.
-
can i ask mate do you have to change the interior loom also? meaning the dash one in a sportif engine swap with a 4efte...
its just that I've swaped the engine and all looms so im bit stuck..
regarding the loom il take it if the price is oryt ;)
-
Glanza v manual 1996 full engine loom + indicator looms.required for my project un-cut with fuse box etc..
-
lovely little car, unabused low Milage!!
Ebay link..
-
Cheap pair of cams for 4efte.
Ebay link..
http://www.ebay.co.uk/itm/Toyota-glanza-camshafts-4efte-starlet-gt-/302341411438?
-
The looms are different.
ahh ryt thanks bud
-
Is it possible to use a engine of a ep91 glanza on a ep82 straight swap?
-
Require a glanza ep91 turbo dashboard..
-
Right after a years messing around finaly got a complete loom..will update in a week or so...
-
Ep82 for sale, will be avalible for sale few days after shes been.mot tested.. if it intrests you..
1994 car in black..
Front mount intercooler
Fpr
Apexi induction kit
speedline alloys (gold)
turbo timer
-
As above as the one on cars bit damaged, from manifold the nut thread on the head has cracked.
-
Require suspension all 4 shockers if avalible cheers
-
As above pm me location and price
-
Mate whats price posted cheers
-
Mates ep82 manifold got a huge crack, so as above need a replacement..
pm me prices please peeps asap
-
1. Ideal'y with a pop'd engine or knocking..
what u got??
2. Also require front indicators..and the bulb loom to go with...as my loom has the front indicators sliced from the loom..
3. 4efte Ep91 Catalytic converter with sensor+plug
4. Dump valve.
5. Coilovers for my mates Ep82
Pm me prices and location.
Thankyou
obx 421 exhaust mani n/a
in Starlet Parts For Sale
Posted
Did this sell?