Jump to content

Sportif 4efte

Member
 View Profile  See their activity

  • Content Count

    249

  • Joined

  • Last visited

 Content Type 

Posts posted by Sportif 4efte

    SR 4efe to 4efe-t Conversion Ecu Plug Question..

    in Electronics

    Posted

    On Wednesday, October 03, 2018 at 10:57 PM, RobSR said:

    Ok so with the way you have done it the below is what I’d do. 

    Firstly the 4efe runs a different kind of idle control valve.

    Id day you have 2 options, don’t run one, or fit a 4efte one. I’d go with fitting the 4efte one - 12v to one side from the Efi relay and then run the other side to the ECU. (Con 1, Pin 10)

    In regards to the second question, the 4efe runs a 4-wire lambda rather than a single wire lambda like the 4efte. One of the 4 wires is the ‘heater’ for the sensor.

    Remove the 4efe 4 wire sensor, and fit a single wire 4efte one and run this to Con 2, Pin 6.

    Hope that helps :) 

    I’ve got 6 wires going to the n/a distributor 4pin plug and 2 pin plug on the glanza ecu I’ve only got a 4 pin plug. So far I’ve chopped the old 2 plugs off and put the glanza distributor plug on(without it being connected to the circuit) not too sure which wire to connect to which pin n what happens with the remaining 2 wires from n/a loom

    N/a 4 pin connector blue green yellow white/black

    N/a 2pin connector black/white/black

    Glanza 4pin connector blue green white red.

    That was the other question he asked me to ask for...

    SR 4efe to 4efe-t Conversion Ecu Plug Question..

    in Electronics

    Posted

    I’ve chopped of the ecu plugs (engine&dash) of the n/a loom and chopped of the 3 glanza ecu plugs of the glanza engine harness and glanza dash loom now I’m using the 3 glanza ecu plugs and connecting the pins to the n/a engine and dash loom (matching the pins) I’ve managed to match up everything apart from 2 pins which are 1 and 15 from the n/a engine loom n not to sure to which glanza pin they go to. 
    N/a engine loom Pin 1 rotary solenoid close-cold idle speed control 
    N/a engine loom pin 15 heated oxygen sensor.

    SR 4efe to 4efe-t Conversion Ecu Plug Question..

    in Electronics

    Posted · Edited by Sportif 4efte

    6 hours ago, RobSR said:

    What loom are you using?

    a GT 4efte one?

    a Glanza 4efte?

    the original 4efe one with the fte bits spliced in? Let me know and ill advise what you need to do.

    You cant easily plug a 3 - connector Glanza ECU into the 2 - connector 4efe loom if thats what you are trying to do.

    Mate yes I'm splicing fte bits into the na loom..

    Wanted Glanza spares or repair.. and few bits..

    in Wanted

    Posted

    1. Ideal'y with a pop'd engine or knocking..


    what u got??



    2. Also require front indicators..and the bulb loom to go with...as my loom has the front indicators sliced from the loom..



    3. 4efte Ep91 Catalytic converter with sensor+plug



    4. Dump valve.



    5. Coilovers for my mates Ep82



    Pm me prices and location.



    Thankyou :thumbsup:


×
×
  • Create New...