-
Content Count
67 -
Joined
-
Last visited
Content Type
Profiles
Forums
Wiki
Media Demo
Store
Calendar
Posts posted by Gav Missen
-
-
Update time she’s finally back on all 4 no more stands 😂🙌
still needs to go back up as I haven’t fitted the wilwoods yet but managed to get the axle back to together new rear wheel bearings, discs pads & calipers back on
Still need to do some adjustment on the suspension to get it sitting right but the wider wings has definitely helped with the fitment on the front may need some adjustment on the rear
Never get bored looking at this
also decided to strip the rear and spray it only done it in high build primer at the moment till I get some more 040 white but it’s a start
-
-
Managed to get the axle back on tonight along with my Gizfab panhard rod not properly adjusted yet only by eye will get a full geo setup once it’s back on the road
Then moved on to the rad had issues with the original grommets fitting the half rad fitting kit so took some advice from @Claymore and sorted some other out cheers bud!
Haven’t attached the hoses yet as I may get a different fan for the rad instead of the ones that cable tie through, also fitted the RW developments expansion tank
-
So got the axle off and it was in a bit of a state
stripped the brakes and back plates off to clean it up as much as I could with a wire wheeltapped up the areas I needed and gave it all a coat in black
still have the callipers etc to paint back in red, new rear bearings have arrived just need to order new discs and pads for the back.
also my Tegiwa half rad turned up today as the half rad I had on was getting a bit tatty
-
Looks pukka bud
-
So bit of a bigger update as haven’t posted in a while..
managed to source some livesports wings to fit the new wheel width still in gel coat yet to be painted
also got the gearbox casing welded up where there was a crack
then managed to finally get the engine in! Feels a shame to be covering up the ORC clutch & fly 😭
gave the gearbox a clean and sprayed it black
then mocked up the turbo and manifold, also fitted the new catch can and lines along with the Cusco brake stopper
now that the abs & p/s are out the way I can mount the fpr here which I think is a nice touch
driveshafts and new seals are now all in but I’m having issues with a wheel bearing that I’ve only just had replaced seems to be locking up tight when hun nut is on will take it off and look in to it more soon.
spent some more time today fitting the loom and taking the rear axle off to be painted will get more pictures soon.
cheers
-
-
Little update
got sick of looking at the state of the old crank pulley
ordered a fensport one and really happy with it build quality looks good
also sent my gearbox off to be repaired, I’m not sure what hillbilly done the last repair but oh my goodness 🤣
pretty safe to say it won’t be staying like that
-
54 minutes ago, jellybaby said:
Looking good feller
Cheers mate, getting closer to the finish line finally!
-
Looking pukka bud, where did you get the Toyota bolt kit?
-
Another update
got some parts test fitted on the engine all looks good so far
Ordered a RE developments catch tank & lines and a coolant reservoir tank
I then split the gearbox in half removed the old diff and gave it a little clean inside
I then fitted my new Kaaz 1.5 way diff and fitted new bearings etc
hopefully during this week I’ll get the ancillaries on the engine sort the engine loom out and start getting everything put back in the bay
also need to get an exhaust made up to match with my 3” downpipe
will keep updated
cheers
-
On 1/20/2023 at 8:55 AM, Claymore said:
Top notch parts there mate, Turbo looks awesome. Looking forward to the build.
Cheers mate hopefully be done by summer 💪
-
Haven’t posted for a while but back on track!
Engine is done and now fully forged I’ll do a spec list later on
The ORC clutch & flywheel arrived from Japan really pleased with that looks a great bit of kit
Turbo arrived from midnite turbos TD04 hybrid billet wheel Greddy 9 blade shaft
Willwood brakes are here ready to go on
WEPR manifold is a real bit of kit looks lovely
Test fitted the wheels and may have to figure something out with the arches or get some wider ones it’s very tight
Think that’s it for the moment just time to put everything together and get the gearbox sorted
-
So update time…
suspension parts are all now back together, even though I’ve got to take the hubs back off to remove the backplates as I’ve just ordered the Willwood 4 pots which should be a nice addition!
i also got the HEL abs delete kit fitted which was a bit of a pain with no instructions but worked it out eventually! Also fitted the new poly bush engine mountsthe Kaaz diff has now arrived just still unsure whether to use my gearbox or now at the repair I found on it may be worst than I think I’ll try and get some photos to show…
also ordered some bronze Grid V’s and some ns2r’s which arrived today!
still waiting on quite a few parts but I’ll keep updated as much as I can
Gav
-
Hi everyone so I’m doing a bit of an overhaul with my suspension I’ve replaced everything
wishbones
droplinks
anti lift kit
24mm arb etc
well.. I’ve just fitted it all up and the near side arb is practically touching the wishbone where as the offside has a bit of space,
will this change once the cars on the ground? I did notice when I removed the old anti roll bar that there were some make shift rubber covers over the arb in that area
offside
thanks
Gav
-
Soo I may have bought some more goodies for G today…
38mm tial wastegate
ORC 309 clutch & flywheel
Kaaz super a diff
Oil sandwich plate
Gizfab panhard rod
Powerflex engine & box mounts
Cusco brake stopper
HEL abs delete kit
HEL braided clutch line
HEL braided fuel line
a new half rad fitting kit as mines getting tatty
-
So fitted some more parts today, forgot to order steering rack gaitors so hopefully getting some more today.
also dropped my hubs off last night to get the wheel bearings fitted so they will be going on over the weekend too.
also prepped my anti roll bar up, gave it a metallic silver base coat then coated with candy apple red followed by 2k gloss laquer, came out quite well -
So managed to get the bay painted and looking tidy 👌🏽
also got the inner arches cleaned and under sealed ready to put all the new wishbones anti lift kit droplinks track rods etc on
all of the suspension parts have turned up now so removed the new bushes off the wishbones and replaced with the anti lift kit ones
-
That’s pukka mate I did keep seeing the videos come up on TikTok! Have you got any future plans for it now?
-
Had a quick hour on G after work, removed the wings just to make it a bit easier to clean everything up and I also plan on condensing down the loom in them areas as it’s very messy and maybe relocating the fuse box inside the car.
had a scrub up in the bay and arches was very grimey under the wings as you can see, getting a bit of prep work done ready for some paint, will also under seal the arches, trying to get this done soon as my suspension parts are slowly turning up so would like it all painted whilst it bare.
Gav
-
Saw this at Shaun’s on Saturday looks pukka 🙌
-
I also put an order in today for the following parts which I want to get fitted before putting my engine back in
powerflex black anti lift kit
lower armslower arm ball joints
arb droplinks
front wheel bearings
inner track rods & ends
hoping to get everything underneath the car new to match everything else
-
-
Not a big update
stripped the following off the car:
brakes
hubs
lower arms
droplinks
anti roll bar
engine/gearbox mounts
inner track rods & ends
Gav’s 98 SPEC 4E FORGED BUILD
in EP91 Glanza Progress Blogs
Posted
Forgot to update this in a while and definitely don’t have as many photos as I’d like 🤦🏼♂️
just been trying to plumb all the electrics in hook up the vacuum lines etc
also made up some fuel lines
Starting to look more like a bay now with some parts from DJR
also finished off painting the boot floor and under the rear seats (I’ll get some more photos of it now with the rear brace and plastics in etc)
intercooler turned up so briefly test fitted it in to place
held the toms bumper up against it still plenty of trimming needed before I can actually fit it but looks soo much better
this is where I am at at the moment struggling to find a long enough turbo oil return 16-19mm for the top mount hopefully will be able to fire her up soon 🙈