CaroleBaskin91

Also might be a stupid question but would it be showing low on oil pressure if it's leaking into the coolant on the headgasket? Logically you'd think it would

Cheers lads! I'll check that video and I got an OEM Toyota one off ID-Workz

Just to give you an update on what I've done. Bought the car as a rolling shell, bought an engine that had knocking on a big end. Stripped it down, re ground the crank and fitted main and big end bearings to match, had a new piston and rod too. Built everything up, put engine and dash looms in, everything is pretty much there now. But.... I've had the engine idling as normal sounds good, but my oil light keeps coming on and stays there even when warm. The oil is going somewhere, and just today ran it up with the rad cap off and there seems to be a bit of foam starting to form when at norm

So my glanza starts up. I'm using an engine bay loom that uses the 3 pin connector on the coolant housing. I can get wiring diagrams up for engine and ECU, but I can't find where the wires should go into the cluster?? Anybody have any diagrams/pinouts for the instrument cluster?

My fuel pump only primes after the engine cuts out. So ignition on, no prime where it should do and then if I crank it and fail to start when I stop cranking the fuel pump primes?? Have I got some wires the wrong way round?

Great info this! Cheers mate

Do you still have the engine loom and dash loom to match?

Hi, I don't suppose you still have the engine loom, and also a matching dash loom?

So I've got two dash looms and want to make one good one, but I need some wiring diagrams. It's for a 97 Glanza dash loom does anybody have any?

Hi guys does anyone know the difference between the 97 and 98 spec dash looms if any?

Engine stand arrived ready to hold the engine I bought for £250.00! That is sump, block all internals and head, rocker cover. Only thing is bottom end has gone. So will strip it and Fixe what it needs

Here are the finished sills, just need to line up and drill the holes for the side skirts and seal them.

I didn't do the welding myself, there was a couple lads off the Facebook pages who sorted it for me, I'll try find their names and give them a shout on here. Top lads!

Ah yes! You might be right there! I will check it to the alternator connector and see if it fits, very good shout that!

Hi guys, got a question some of you I'm sure will know the answer to. I have bought a Throttle position sensor and the plug on the loom doesn't fit. I'm guessing this is the correct plug but it's a different shape? My glanza is a 97, but I can't be sure this is the same loom from new, any info on it?

Yeah was a big suprise, he hadn't told me about the sills at all no. Which was naughty. Anyway I will post more updates up tonight, as I got both sills replaced

Now started my glanza build its under 🔥 Lockdown Glanza 97 build

Managed to find some top lads who said they'd have a look at it see how much work it needed. So got it on a flat bed and took it to a barn in Derbyshire to check out the condition of the sills and the rest of the underside ...

The day after it arrived when I could actually see in the light. I went straight to check the sills as I realised I could see a little rust under the skirt 👀

The specs on it : Imported in 2010 manual 140km so only around 80k miles on the car Body work looked pretty good on the outside. Obviously I didnt see the car at all so I knew it was a bit of a gamble. Anyway I gambled and this is what I discovered when it arrived ... 1890725798_screen-20211030-1719223.mp4

Hi all! I have done a build on here before on an Na to turbo build. Now sold and this is my next project. I'll have to backtrack a little as I'm already a way into the build, not had time to make a build thread until now. So I bought this as a rolling shell, no engine no gearbox no exhaust just the wheels suspension and brakes and bottom arms, all steering gear there but nothing in the terms of engine. As it was in lockdown still at the beginning of 2021 January I couldn't travel to view or buy a car. I saw this was for sale and thought I would take a punt on it! And get someone