Curtis

yeah i reckon the little twat would keep his mouth closed after that lol

and watch him push his roof in more lol

that look lovely mate i really like that. looks a 1000 times better with them wheels on.

imagine how difficalt it would be to turn it back over lol

sounds good buddy should only cost bout £100ish i reckon if you don't change the clutch. i think you had a bit of a deal there mate

1. a screwdriver through the roof. insurers will right the car off as a uneconomical repair. 2. engine flush in the oil. little chavs willbe well chuffed to figure out that all the molicues in his oil are not lubricating there engine. 3. tie a thick row rope round his driveshaft and tie the other end to something heavy e.g drain cover, lamp post, another halfords chav special car. as the rope wraps up Bang!!! imagine the damage of a drain cover being smashed into the gearbox. 4. chemical metal down the door shuts, very funny watchin him tryin to get in his car. 5. use a garden hose

fort ou would bud lol i would do the same. what you got to get done to the sr

i think you also broke the bumper mounts didn't u lol. something tells me toyota are finding getting a 96-97 a bit difficalt and they can get you a facelift bumper and mounts. yea dam right bud get it done properly

ya i am a nice bloke really lol. not really sure mate if anyone wants anymore i have loads of em lol

no way buddy, the other half just told me, hope your ok, i would go to toyota for your parts replace it like for likeand go to top quality bodyshops for your quotes. ain't your fmic damaged at all. speak to you later mate curt

how about put a small hole in the rear light cluster, run wires to the brakelight, remove the petrol cap and put the other end of the wires in there and refit the petrol cap. conclusion: the bloke wishes he had a fire extinguisher in his car after he presses the brake

mine is curtsstarletsr@hotmail.com don't mind if anyone adds me as long as i don't get sent junk e.g penis enlargement crap and so forth lol

looks nice buddy. there is a downside to spacers unless you get hubcentrc spacers the spiggot ring will not sit on the hub, so the whole weight of the car will be on the wheelnuts, it has been known if there is no spiggot rings fitted to wheels or masive spacers been used is that the nuts/studs snap and your wheel comes off. hope this helps curt

1) Bourkey & SR + Girlfriend 2) rob_bower & SR + Missus 3) Craig_N & Glanza S 4) Bluebear & Sportif 5) Sparky & GT + someone tongue.gif lol 6) Starbogt & GT + Wife n Kid 7) BAZ2CRAZY+people Galliano + Galliano + mum 9) Streetracer + "maybe" her. 10) Ben + GlanzaV + Isla (girlfriend) 11) Starlet Nath & SR + Wife 12)Gary_EP91+Starlet+Samantha(girlfriend) 13)Starlet_Tim + Starlet + A Piece Of Meat Or Bro 14)Markoos & Glanza V + Missus 15) Al & Glanza V + possibly missus 16) AlexGTAdv and the slag(GT)+maybe laura 17)Matt Glanza glanza V.maybe the missus 18) Cra

happy birthday buddy, joz he only let slip to us last night lol

put a little slit in the bottom rad pipe off, the fucker won't realize until the engine goes pop, as you say he leaves it down your road overnight the car will be cold, and then the little numpty will go for a drive, by the time he figures out the car has not warmed up he won't have any piston rings left. if you are going to do this make sure it isn't a straight cut on the pipe or it will look obvious (make it look like wear and tear)

bugger! i was winning till today lol

thanks buddy, hopefully gettin the speedlines on in a couple of weeks, still don't know what colour to get them refurbed yet tho lol

thanks bud, can't wait to get the speedlines on and lower it thanks, the only bit on the engine that makes it a bit grubby is the rubber o rings where the bolts are to hold on the rocker cover are seeping a bit its a manual, picked it up with 140,000k on the clock not to bad anyway as i will pos forge it or put a low miler in it. thanks for all the comments curt

hi buddy you should have 4 wires with it, the red is switch live, yellow permanent live, black earth and there should be one more wire not sure on colour tho, that one will go to the ignition module to the negitive side. hope this helps curt

thanks buddy, there is a couple of marks on the bodywork but not much, think i got a good deal the other plan for the wheels was blue centre with flake and white lip nd logo not sure yet tho. gonna put the wheels on when it gets lowered. gonna go for spax 40mm springs first till i can pick up some decent coilovers. curt

hi ya everyone after months of waiting for a good day till i can clean my little v (typical bloody uk weather) and eventually i gave it a good wax today so now i can start my built thread. i got her about 2ish months ago i have big plans for her, i already got my bov and induction kit. the other half should be getting a sr soon so i will be getting the speedlines off her, i have a tub of house of colour mini kamon blue metalflake sitting in the shedso the speedlines will be refurbed with a electric blue lip with the centre having a white and metalflake coating and to finish them off have the

holy shit that is some sexy lookin v i have never seen it before. nice one geo

hi and welcome to uksc, hope you enjoy your stay