gwtaylor Posted March 9, 2019 Share Posted March 9, 2019 Just bought this ill get full spec up later any comments welcome good or bad Quote Link to post Share on other sites
gwtaylor Posted March 9, 2019 Author Share Posted March 9, 2019 Jobs to do put induction kit on refix front bumper on sort all without needs washer bottle Quote Link to post Share on other sites
gwtaylor Posted March 10, 2019 Author Share Posted March 10, 2019 So is this an upgrade exhaust manifold can’t see and make on it hope it’s not a cheap Chinese job and will it really make that much of a difference as it’s still running stand turbo Quote Link to post Share on other sites
akyakapotter Posted March 10, 2019 Share Posted March 10, 2019 Looks like a Zisco manifold. Quote Link to post Share on other sites
maerijn Posted March 10, 2019 Share Posted March 10, 2019 Zisco ramhorn You wont have any problems with cracking manifolds for a while, thats for sure. Should've polished it before fitting Quote Link to post Share on other sites
gwtaylor Posted March 11, 2019 Author Share Posted March 11, 2019 7 hours ago, maerijn said: Zisco ramhorn You wont have any problems with cracking manifolds for a while, thats for sure. Should've polished it before fitting It came with the car bud already fittrd Quote Link to post Share on other sites
gwtaylor Posted March 15, 2019 Author Share Posted March 15, 2019 Right managed to get around the car today between down pours Quote Link to post Share on other sites
gwtaylor Posted March 15, 2019 Author Share Posted March 15, 2019 Right it’s got an aftermarket rad but the fan isn’t wired up can anybody tell my if this is a suck or blow fan? Quote Link to post Share on other sites
LeonL Posted March 15, 2019 Share Posted March 15, 2019 (edited) You can swap wires around and it’ll spin opposite way. but based on fact it’s on rear of radiator it should be pulling/sucking heat out of the radiator Edited March 15, 2019 by LeonL Quote Link to post Share on other sites
gwtaylor Posted March 15, 2019 Author Share Posted March 15, 2019 3 hours ago, LeonL said: You can swap wires around and it’ll spin opposite way. but based on fact it’s on rear of radiator it should be pulling/sucking heat out of the radiator Yea I did that like noticed it span both ways like just trying to work out which way it should spin like Quote Link to post Share on other sites
gwtaylor Posted March 15, 2019 Author Share Posted March 15, 2019 Doing abit of wire searching and luckily I have a complete ish car for reference Quote Link to post Share on other sites
LeonL Posted March 15, 2019 Share Posted March 15, 2019 (edited) You’d be able to tell if it’s blowing or pulling by feeling the air around it while turned on Edited March 15, 2019 by LeonL Quote Link to post Share on other sites
gwtaylor Posted March 15, 2019 Author Share Posted March 15, 2019 5 minutes ago, LeonL said: You’d be able to tell if it’s blowing or pulling by feeling the air around it while turned on Yea I can tell that but which way should it be working pulling or pushing air bud that what I’m trying to work out Quote Link to post Share on other sites
LeonL Posted March 15, 2019 Share Posted March 15, 2019 (edited) Because it’s mounted on the back of the radiator it should be pulling air/heat out of the radiator and into the engine bay if the fan was mounted on the front of radiator you’d want it pushed the heat through and into engine bay Edited March 15, 2019 by LeonL Quote Link to post Share on other sites
gwtaylor Posted March 15, 2019 Author Share Posted March 15, 2019 4 minutes ago, LeonL said: Because it’s mounted on the back of the radiator it should be pulling air/heat out of the radiator and into the engine bay if the fan was mounted on the front of radiator you’d want it pushed the heat through and into engine bay Cool that clears that up cheers bud Quote Link to post Share on other sites
gwtaylor Posted March 15, 2019 Author Share Posted March 15, 2019 Right one more job done thanks to Leon next job the front antirillbar is hitting the lower arms its an aftermarket one what can be done to stop this happening Quote Link to post Share on other sites
maerijn Posted March 18, 2019 Share Posted March 18, 2019 it seems to be sitting very loosely in its bushings Quote Link to post Share on other sites
gwtaylor Posted March 18, 2019 Author Share Posted March 18, 2019 6 hours ago, maerijn said: it seems to be sitting very loosely in its bushings Ok so it should be a lot tighter how tight? any tourqe settings? Quote Link to post Share on other sites
LeonL Posted March 19, 2019 Share Posted March 19, 2019 Normally you tighten them up quite abit until the bushing become squashed down. I don’t have any torque settings I’m afraid Quote Link to post Share on other sites
gwtaylor Posted March 19, 2019 Author Share Posted March 19, 2019 5 hours ago, LeonL said: Normally you tighten them up quite abit until the bushing become squashed down. I don’t have any torque settings I’m afraid Ok bud ill do that Cheers Quote Link to post Share on other sites
Di_Bodi Posted March 19, 2019 Share Posted March 19, 2019 That's how much the OEM where squashed (before I've changed to TRD arb): Quote Link to post Share on other sites
gwtaylor Posted March 22, 2019 Author Share Posted March 22, 2019 Well took some more pictures today of ARB defaniy needed tightening completely tightened both both sides but still rubbing so think I’ll have to get some ARB spacers made Quote Link to post Share on other sites
gwtaylor Posted March 22, 2019 Author Share Posted March 22, 2019 While I had it up in the air I decided to take exhaust off as I’ve got a full blitz system to go on even though this one did sound ok like. but it will be going up forsale this evening Quote Link to post Share on other sites
gwtaylor Posted April 16, 2019 Author Share Posted April 16, 2019 No real pictures yet but have a blitz exhaust to be fitted another half rad a new actuator and just fitted 16” team dynamic alloys. noticed a clunk from the rear end and after investigation it was the bushes in the rear diagonal bar. Luckily I had a spare from the one I’m breaking to go straight on job done. Quote Link to post Share on other sites
gwtaylor Posted April 22, 2019 Author Share Posted April 22, 2019 well investigated why my rear whiper has never worked so did a little digging and found out exactly why LOL! Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.