Mikey Jay Posted February 23, 2007 Share Posted February 23, 2007 Riteo, is a cf thing to do then? Quote Link to post Share on other sites
*Toymota* Posted February 23, 2007 Share Posted February 23, 2007 it happened to my mate in his subaru type r too and it nearly happened to me many times before the bonnet pins!! Quote Link to post Share on other sites
Toby@ToyTuning.com Posted February 23, 2007 Share Posted February 23, 2007 As mentioned as long as you use bonnet pins you should have no trouble at all, we use the embeded carbon ones like they sell on driftworks.Kind Regards,Toby Quote Link to post Share on other sites
SiCaln Posted February 23, 2007 Share Posted February 23, 2007 these ones?Driftworksim gna run these too Quote Link to post Share on other sites
Toby@ToyTuning.com Posted February 23, 2007 Share Posted February 23, 2007 Hi Si,Yes those are the ones, quite safe as well although I still have the oem bonnet release.Kind Regards,Toby Quote Link to post Share on other sites
*Toymota* Posted February 23, 2007 Share Posted February 23, 2007 if id of known you can get them, id of got them instead! i cant put them on now can i? Quote Link to post Share on other sites
Sparky Posted February 23, 2007 Share Posted February 23, 2007 My stock n/a bonnet looks like its gonna rip off at high speeds Enzo mentioned single wipers... i was just wondering if they are available for the ep91 I've seen em for ep82s but not the 91s Or does anyone know if the 82 ones would fit the 91?? Quote Link to post Share on other sites
StarletRick Posted February 23, 2007 Share Posted February 23, 2007 single wipers are mega chav. dont do it! and drilling carbon...tape it up on the top side, and drill an uber small hole as pilot, then get a tapered drill to open the hole up SLOWLY. then stick some glue in it to seal. let it dry and off you go. Quote Link to post Share on other sites
Nanglebadger Posted February 23, 2007 Share Posted February 23, 2007 those look ube geo mate, nice find, keep us posted!Phil. Quote Link to post Share on other sites
Sparky Posted February 23, 2007 Share Posted February 23, 2007 Each to their own Rick mate Touring Car drivers are chav????? Quote Link to post Share on other sites
SiCaln Posted February 23, 2007 Share Posted February 23, 2007 oh was it single wiper, i thought u just replaced the oneoh no the ube has landed, damn u Rick Quote Link to post Share on other sites
lobotomy Posted February 24, 2007 Share Posted February 24, 2007 I think the thing Geo is looking at is a bit that clips onto single wiper arms... not a conversion (as far as I'm aware.) Quote Link to post Share on other sites
olive Posted February 24, 2007 Share Posted February 24, 2007 I still havent fitted the pins to mine yet lol 2 scared Quote Link to post Share on other sites
Guest Enzo Posted February 25, 2007 Share Posted February 25, 2007 I think the thing Geo is looking at is a bit that clips onto single wiper arms... not a conversion (as far as I'm aware.)yea mate thats the craic Quote Link to post Share on other sites
Glanza_Ragger Posted February 25, 2007 Share Posted February 25, 2007 done this last weekend, piece of piss enzo.masking tape the bonnet up roughly where your jets go.mark up in pen the shape you need, measure it and make sure there not pissed.drill the center hole with a tapered drill bit, (the type that has a tiny point , leading to the stanard drill part)then use a small square detail file to file for the pins either side of the hole.dont go over kill or you will have a gaping hole around the edge of the jet.mine fit extra tight, which is good because they dont leak through.on the underside once mounted, use a bit of mastik to seal around the edges. et voila done.just drill using a hand drill , and file extra slow and gentle with out much pressure and it wont chip the carbon. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.