ToyotaTech15 Posted September 13, 2011 Share Posted September 13, 2011 Had half an hour to spare tonight so went about fitting the tc short shifter I've had sitting for ages.I fitted the shaft itself, but I'm left with 6 small silver shims, 2gold shims and 2 gold snap rings,Where do these left over bits go?Ill be back at it soon but couldn't think where they went, Also it's on a ep91 if that makes a differenceCheersG Quote Link to post Share on other sites
rob_bower Posted September 14, 2011 Share Posted September 14, 2011 Gaz they go under the selector its self to lift it up so the shaft clears the floor! I don't think I used them all on mine! Quote Link to post Share on other sites
ToyotaTech15 Posted September 14, 2011 Author Share Posted September 14, 2011 Yeh I've got 4 big silver shims which I thought were for the bottom of the selector but I still have 2 big snap rings, 6 small silver shims and another 2 gold pieces that look like they join with the snap rings? Did you use all the parts that came with your kit or was their some left over? I'll maybe have to get pictures to show what bits I have left. G Quote Link to post Share on other sites
rob_bower Posted September 14, 2011 Share Posted September 14, 2011 no i dont think i did i seem to think there were a few bits left! get a pic of what you have gaz and ill have a look at mine jog my memory! Quote Link to post Share on other sites
turbo Grant Posted September 14, 2011 Share Posted September 14, 2011 Have you fitted the solid bushes that go on the selected cables at the gear box? Quote Link to post Share on other sites
rob_bower Posted September 14, 2011 Share Posted September 14, 2011 ah yes that would make a little more sense with the brass bushings! Quote Link to post Share on other sites
ToyotaTech15 Posted September 14, 2011 Author Share Posted September 14, 2011 Not fitted anything to the box cause the shifter is out of the car, Had a feeling something had to go at the box as there was so much left over lol.I'll keep the other bits until I fit the engine back inCheers Quote Link to post Share on other sites
rob_bower Posted September 14, 2011 Share Posted September 14, 2011 yea the kit came with solid shifter bushes! stick a pic up though gaz lets have a look whats left! Quote Link to post Share on other sites
ToyotaTech15 Posted September 14, 2011 Author Share Posted September 14, 2011 Ok I'll get a pic tonight bud, Quote Link to post Share on other sites
WallaceGlanza Posted September 14, 2011 Share Posted September 14, 2011 Yeah the brass/gold pieces together with the snap rings/circlips are definately for the gearbox selctors to replace the rubber ones. Not sure on the other 6 shims though, however I definately used all the bits when I fitted my TC kit.There is a guide on here somewhere I think, but may have been in the TC trading section which is obviously gone. Quote Link to post Share on other sites
ToyotaTech15 Posted September 15, 2011 Author Share Posted September 15, 2011 Got a pic tonight, obv I know where the 4 big silver spacers and where the brass bushes and circlips go, But where do the 6 other shims go? Are they from this kit as I think they may have fallen in the box from something else??G Quote Link to post Share on other sites
rob_bower Posted September 15, 2011 Share Posted September 15, 2011 The 2 brass bushes and c clips are the shifter bushes then!One of the large bushes in each corner of the shifter with one small one on the top of the front 2! And the last 4 go on top one in each corner of the shifter! HthRob Quote Link to post Share on other sites
ToyotaTech15 Posted September 15, 2011 Author Share Posted September 15, 2011 Ok that's fine Rob thanks for your helpI won't need any of the silver spacers as Im making a custom bracket to lift the selector up higher someone need to space it away from the floorG Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.