EPnick22 Posted May 31, 2013 Share Posted May 31, 2013 right ive just wired up my speed limit defencer, went for a quick test to make sure it works and it does, car doesnt run any differently in the slightest, everything smooth as always, when i booted it down the motorway my engine management light came on, i pulled over in the lay by, checked my oil and was real low (changing it today) when i turned my ignition back on, the light was gone, then when i booted it again it came on? i have FCD fitted but its never done this before Quote Link to post Share on other sites
StuDoc 72 Posted May 31, 2013 Share Posted May 31, 2013 FCD's are an accident waiting to happen. Sorry this doesn't help you but its true. Quote Link to post Share on other sites
H_D Posted May 31, 2013 Share Posted May 31, 2013 Have u done a diagnostic check? Any codes come up? Quote Link to post Share on other sites
EPnick22 Posted May 31, 2013 Author Share Posted May 31, 2013 FCD's are an accident waiting to happen. Sorry this doesn't help you but its true.what would happen then? its been in there for a few years, runs a bit rich, nothings changed, but why would the light come on?Have u done a diagnostic check? Any codes come up?not yet it only happened today, im going to try getting it plugged in during the week at some point! Quote Link to post Share on other sites
EPnick22 Posted June 2, 2013 Author Share Posted June 2, 2013 bump!! apparently my local garage cant plug the car in due to not having an OBD port? how am i meant to know what my eml is coming on for?! Quote Link to post Share on other sites
akyakapotter Posted June 2, 2013 Share Posted June 2, 2013 Do the test your self id say its the start of fuel cut as your now able to go faster CLICK HERE Quote Link to post Share on other sites
EPnick22 Posted June 2, 2013 Author Share Posted June 2, 2013 its never done it before though, and i can redline every gear (not that i do ) full boost etc and it doesnt come on, i could just be cruising off the boost and itll randomly come on, then disappear when i turn the car off, then on again? Quote Link to post Share on other sites
akyakapotter Posted June 2, 2013 Share Posted June 2, 2013 do the test in the link above bud and it will tell you whats up Quote Link to post Share on other sites
EPnick22 Posted June 2, 2013 Author Share Posted June 2, 2013 i read that all through and im beyond tired at the moment so maybe have a look tomorrow ill give it a go Quote Link to post Share on other sites
akyakapotter Posted June 2, 2013 Share Posted June 2, 2013 will take you less than 5mins to do it all you need is a paper clip pen and pad to wright down the result Quote Link to post Share on other sites
EPnick22 Posted June 2, 2013 Author Share Posted June 2, 2013 a paperclip to connect the 2 pins up right so it appears on the dash? Quote Link to post Share on other sites
akyakapotter Posted June 2, 2013 Share Posted June 2, 2013 yep to bridge te1 and e1 then ignition on and see how may times the eml flashes will flash say twice then seven = code 27 ect Quote Link to post Share on other sites
rkane Posted June 3, 2013 Share Posted June 3, 2013 Knock Sensor Quote Link to post Share on other sites
EPnick22 Posted June 3, 2013 Author Share Posted June 3, 2013 explain more? Quote Link to post Share on other sites
akyakapotter Posted June 3, 2013 Share Posted June 3, 2013 Did you do the test bud ? Quote Link to post Share on other sites
EPnick22 Posted June 4, 2013 Author Share Posted June 4, 2013 i havent have time dude been working my nuts off lately, I'm going to see what im doing tonight, it hasnt come on now for 2 days (the light) that mean anything? Quote Link to post Share on other sites
Fisher Posted June 12, 2013 Share Posted June 12, 2013 if you test it she will proberly show fault code 42 like mine did as my cable was not connected (that's my speedo cable by the way) check my linkhere http://www.ukstarletowners.com/topic/66490-ecu-diagnostic-codes/ basically ecu code 42 Vehicle Speed Sensor (VSS)No speed sensor signal to ECU when loaded driving condition with engine speeds 2000 to 5000 rpm. in 5th gear drivingFor 8 seconds or more. check it out pal see if the link helps Quote Link to post Share on other sites
EPnick22 Posted June 13, 2013 Author Share Posted June 13, 2013 I'll check that at some point after work today dude, sounds like the most likely problem! I just thought it was funny how even when i dont boost it came on, but if i go boosting around it didn't come on haha if you test it she will proberly show fault code 42 like mine did as my cable was not connected (that's my speedo cable by the way) check my linkhere http://www.ukstarletowners.com/topic/66490-ecu-diagnostic-codes/ basically ecu code 42 Vehicle Speed Sensor (VSS)No speed sensor signal to ECU when loaded driving condition with engine speeds 2000 to 5000 rpm. in 5th gear drivingFor 8 seconds or more. check it out pal see if the link helps Quote Link to post Share on other sites
Fisher Posted June 13, 2013 Share Posted June 13, 2013 keep us updated mate if it aint fault 42 you will be able to find out by doing the test on that above link Quote Link to post Share on other sites
EPnick22 Posted June 13, 2013 Author Share Posted June 13, 2013 keep us updated mate if it aint fault 42 you will be able to find out by doing the test on that above link cheers buddy, I'll have a crack at it when i get in from work (if it isnt raining lol) Quote Link to post Share on other sites
EPnick22 Posted June 13, 2013 Author Share Posted June 13, 2013 found out what it was! you were right dude it was fault 42, which makes sense as it only started happening when i wired my SLD in, have i wired it in wrong lol? Quote Link to post Share on other sites
SpenceGT Posted May 29, 2017 Share Posted May 29, 2017 How do you bridge them te1 etc what all do you need to dobtain it cheers Quote Link to post Share on other sites
akyakapotter Posted May 29, 2017 Share Posted May 29, 2017 How do you bridge them te1 etc what all do you need to dobtain it cheersBridge te1 and e1 with a paper clip turn ignition to ignition on eml will flash up with codes or constantly flash if no faults stored.Cheers nick. Quote Link to post Share on other sites
turbominicooper Posted May 29, 2017 Share Posted May 29, 2017 https://youtu.be/awahKqzyWUQ Quote Link to post Share on other sites
SpenceGT Posted May 30, 2017 Share Posted May 30, 2017 Cheers ladds Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.