Adeeb1395

Can anyone tell me the name of the black plastic tank beside the fuel filter and how to connect it? It looks to be a part of the fuel system and may be works as a fuel tank's blow by gas collector or something not sure. Pls let me knw asap. Thanks in advance

can anyone provide me the diagram for wiring the pwr ect manu switch for the 4age auto tranny and ecu??? urgent help needed pls!!! THANKS IN ADVANCE

Anyone?

i hv a 4efte harness which is completely destroyed by a mouse!!! so the wires are damaged and some connectors/jack are missing. what sensors does 4efte has extra than a 4efe?? air temp, knock, boost solenoid and different connector of distributor igniter and coil. anything else??

need a set of all good 4efte engine wiring but cant locate one here around my place. but heres plenty of 4efe harness. how to use the 4efe harness on 4efte??? what are the differences?? i am assuming need to rewire the ecu pinouts....... any help guys??

I have a 4efte whole engine and a 5e block pistons and con rod. I want to build a 5efe utilizing the 4efte. I knw the block and con rod height is different. And pistons r too. Is it possible to just install the 5e block con rod and pistons? Or i wud face any prob? Can i use the 4efte crank with the 5e block rod and pistons? Tia.

Is this the proper way to convert our distributor to coil pack ignition system using honda d17 coils from 2003-04 civic?? i doubt it as its so easy to do!!!

yeah was thinking about doing that. as there are no threads here or hint on web. by the way thanks for the help

Going to use the full ignition system distributor, ignitor, coil and HT leads

Its 5e that i m converting to 4efte distributor. Doing this convertion as the old distributor dont have both the cam and crank pickups like 4eftes. And i need those pickups to wire the aem fic6 and get it started. The car dont start with aem without this.

i hv checked the connections with multi-meter. the igniter receives BLUE & YELLOW wire from the 4 pin connector and BLACK wire from the 2 pin connector the coil receives BLACKbrown wire form the 2 pin connector to the coil's + point the rest wire which is RED & White from the 4 pin connector goes to some kind of sensor.

can you pls tell me or mark this pics. wud be very grateful!!!

Need the internal coil distributor wiring (4 plug wires and 4+2 wire connector type) Going to external 4efte coil dizzy and ignitor setup!

Some one told me there is a water line in 4efte head which needs to be blocked to install it on 5e? May be i read it on 5efte thread by tgtt

My ep82 engine is 5efe. It creates high engine bay temp. But the engine temo is fully fine. Problem is my car revs 1500-1200 when cood start. When it comes to warm state the rev is fine. But if i sit idle for about 10-20 mins keeping the car on the rev falls to 500-700. If the ac is on it falls more quickly. When i open the hood i can feel the heat strongly. Cant even touch the inlet mani. What can b the problem? I have raised my bonnet Made vents on front bumper bigger Installed gt hood with turbo vent Bypassed coolant line on throttle body Installed ae100 double core full size radiator Nex

My 5efe is running with 4efte inlet manofold. And as i have a 4efte extra engine i want to install its head to my 5efe.(turboing it) What are the things i need to be care of? And will i face any difficulties, arent they bolt on? Tia :-)

1.can anyone tell me the part numbers to identify a 3sgte map sensor?? 2.is 3sge and 3sgte map sensor same?? 3.will there be any problem is i use 3sgte map sensor instead of 4efte??

When i cold start my car and turn on the ac, it normally turns on but after few minutes the ac light goes out and dont cool. i tried no/off the ac but dont work and the ac light dont light up! Any guess what could be the problem??? thanks in advance!

thank you for the diagram. these thing shows some differences. my black wire is connected to pin no 24 and the diagram shows that it should be connected to pin no 13 but both of them are earth/grounding. so should i change it?? my yellow wire is connected to pin no 7 and the diagram shows that it should be connected to pin no 8 but the pin in my ecu is blank which is no 8. what do u suggest to do?? Thanx in advance

my car is a starlet with a 5efe in it and powered by 4efe ecu with rev limit of 7200rpm. i want to install Bee-R rev limitter. Though i hv installed it following a diagram form this forum and it works. but the problem is, 1) it gets pass by the limit which i have set in the limiter when i full throttle it. 2)The car jerks when on the go while cutting rev. is these normal?? and it doesnt shoot flame or fart as it should. here is my ecu pinout Connector A 1) IPV 2) NSW (neutral start switch) 3) THW (water temp) 4) PIN (vacuum sensor) 5) THA (intake air temp) 6) IGT (ignitor) 7) IGF (ignitor

Ok then, but what about the pressure plate? Is that stage 1?

yes there are numbers on the pressure plate!!!

R u sure?

https://www.facebook.com/photo.php?fbid=10203115276434867&l=c2fbc52964 https://www.facebook.com/photo.php?fbid=10203115276434867&l=c2fbc52964 https://www.facebook.com/photo.php?fbid=10203115276954880&l=a9d993d7d3 https://www.facebook.com/photo.php?fbid=10203115277274888&l=64ffe74137 https://www.facebook.com/photo.php?fbid=10203115277514894&l=e6f78e4d73 https://www.facebook.com/photo.php?fbid=10203115277754900&l=0c1758b0a8 https://www.facebook.com/photo.php?fbid=10203115278394916&l=591639f6de https://www.facebook.com/photo.ph

https://www.facebook.com/photo.php?fbid=10203115275874853&l=fa8eddec15 https://www.facebook.com/photo.php?fbid=10203115275394841&l=2b920193ba https://www.facebook.com/photo.php?fbid=10203115275474843&l=e4bd8e754d https://www.facebook.com/photo.php?fbid=10203115276154860&l=33b9f64e5b https://www.facebook.com/photo.php?fbid=10203115276194861&l=e127a0d876 this gearbox is currently installed in a 4efe engine.the car is ee100 with 220kpmh speedometer. at the second pic there is a code written which is 70402604 as far as i can read. lol Any idea