decdd19

il have a look next time im at thanks mate

which sensor off thermo housing? whats the aircon sensor look like? ive all them aircon sensors removed along with charcoal canister

thanks mate got the stuff i got off you fitted worked bang on got a few blitz goodies today picked up a blitz decat, blitz dumpvalve and blitz dual sbc spec r wiried in the boost controller but have to pipe it up still fitted the decat which allowed me to fit my fujitsibo power getter exhaust system (mocked up as i need rubbers for hangers) sounds savage quite enough idling but a nice tone when car is revved fitted blitz dumpvalve works well and sounds the part tidied up wiring under the drivers dash and fitted most interior panels back on starrting to become a car again

let it warm up to near 90 degrees today and didnt work no matter what way i tried it any more ideas must be something i missed

anyone used one of these on the vent pipe from the fuel tank in the engine bay for motorbikes but thought it might work the same maybe http://www.ebay.ie/itm/RFX-Fuel-Petrol-Tank-Gas-Cap-Vent-Tube-Breather-Pipe-One-Way-Valve-Gas-Gas-Red-/121538318929?hash=item1c4c3f9251:g:NpUAAOxy0bRTFd~6

fitted slim line fan , the plug for the fan off the loom is two wires behind passenger side headlight white plug blue and white wire if i remember i also have bulkhead sensors removed the fan doesnt kick in at all maybe i have the wires wrong way around checked fan an that works if i earth on of the wires of the four pin plug in front of the rad for the aircon it turns on but doesnt cut out any help appreciated

gonna pick up a boost and need a a/f gauge to probably 52mm and fit them in pillar pod

not a whole lot happening here just trying to sort wiring picked up defis as a xmas present for her look the job in the zep gauge pod will look better againg once fitted properly

Defi bf 60mm gauges with all sensors and control unit sandwich plate and water fitting (oil temp , oil pressure , water temperature)

after much stalling and putting it on the long finger i made up my earths and went about starting it disconneected fuel pump and removed oil return to check for oil pressure didnt take much cranking to get oil out of the return so bolted back up connected up fuel pump and after a few cranks she fired up very healthy sounding engine, mind you i bought it with out evening hearing it run, warmed up spot on alot of vaccum hoses are temporaily blanked until i can get proper blanking plugs... bled the clutch and all is fine in that area taking all gears nice an smooth no leaks been the most important thing went and fitted my front brakes braided lines abs sensors and arch liners everything fits in snug put all the front suspension in and tightened up just need to get new droplinks for front arb and fix a bolt i rung off in the abs sensor bracket so decided to take it for our first drive around the yard not a whole lot was done as i have to bleed up my brakes but all is sweet as a nut plans over the christmas are wiring needs tidying in the bay and badly inside the car and needs a serious clean out inside also having a good hard think on what i want to do body wise bumpers skirts etc and what manifold and turbo i want to run pretty much over the worst of it so should make serious progess in the next few months

Do me a good Xmas discount on new headlights indicators and headlight adjusters iddy 😊🎅

No not that far yet but soon hopefully

I owe you a can so got oil pressure an currently looking at it as she ticks over sweet as a nut Thanks for the help mate

Perfect Yeah have noticed alot of dampness around the bay lately even with it covered etc thanks for the advice mate

Hi lads looking to start my 4e for the first time in a good while going to disconnect the fuel pump and crank it to make sure I've oil pressure going to disconnect my oil return should I expect much oil or just a small tricle ?? Thanks In advance

Sorry for hijacking the thread but where did you get the rebuild kits?

Id workz cooling panel came and is absolute quality will look even better with bumpers and lights on 😊 Starter on just need to make up my earth's the weekend and grow a pair and fire her up ha 😂

Appreciate it thanks

There's another 1 like the oil pressure sensor connector at the back of the box say in the loom with a thick single black an red wire?

Perfect I know it then was thinking it must slide on... Thanks for the help

Where does that plug in? I don't think so have one plugged into the box, hardly air intake temp sensor

First few are off the sensors on the bulkhead fairly sure I can do away with them the last 3 are the head scratches connector then picture of wire to try help

This is going to be something special altogether fairplay mate what sort of power are you after?

That's very handy thanks mate Will get pics of mine tonight

would the gt one help narrow it down at all? will do tomorrow at somestage