SRdan

Hi all Been a rough couple of months. Made some good progress on the SR a few weeks ago. Since then one of my lads has had some serious health problems so lost all interest. I'm gutted but what's gone on has knocked me for 6, really don't have time to Finnish her off so not sure what I'm doing with the SR just yet

No sorry bud. Last clear one I tried taking off ended up snapping

Got a black Glanza spoiler here with one in bud. 40 posted for spoiler and light

I'll have a look see if what will work. Could save a job doing it that way also. Is it removable then? I haven't looked as haven't got round to that bit tbh

little update. The sr is all back together 98% done now. just have the tps and map connectors from the 82 loom too add and split the thermo wires from the single 4efe connector to run 3 connectors for the 82 engine. then add fluids and bleed clutch then it should fire up. id be telling porkies if i said this was easy, but in all fairness it has not been overly hard. hoping to have it all done and boxed off by next weekend, id imagine there will be a few teething problems as with any engine swap.

PM on way James.. I've managed to get the high pressure one to fit. Just the low pressure one I need

I'm after a 4efte power steering hose for my conversion. After sending money for one off of a lad on one of the Facebook page's the lad has decided not to respond. Someone help please. Tia

Started stripping my 82 loom. Tracing the wires I need back to ECU etc and labeling them as to where they will go on my 4efe loom. So far all seems easy enough, few more connectors to sort as the 4efte had 3 connectors to the thermostat housing rather than just the one. Anyway I'm writing down what I'm doing as I go and taking pictures. Will also be writing what wire goes where etc. Will post up a how to thread if anyone feels this would be helpful. Big benefit with doing it this way is you shouldn't have to touch the interior (apart from adding ecu and few wires to it)

Did think this myself as had the det3 already wired in. However coil is completely different and much safer with knock sensor. Also fte ecu is able to read boost where as the standard ecu doesn't. The det3 just chucks fuel in with the boost rather than read anything (in piggy back anyway) not sure on standalone

Got some here going cheap. Tyres got really decent tread £80 They are black though

engine is in. now im currently fitting the 4efe loom to everything that it fits, once ive done this i will take off the sleeves and add and take away what bits i need/dont (it really isnt that much) then re-sleeve.. not the best way to go about it but will make ity easier to trace back wires etc hoping to be back on the road for next weekend

yes bud thats the only issue i can see. i have the ep82 fuse box here so i can see what goes where.. sounds like a nightmare but i really do think i can have the wiring done over a weekend

yeah that pretty much what im going to try. read a few builds now of people just adapting the 4efe loom to take whats needed. this way round you don't need to touch the interior. heres a little gem i found on another page.. This seems like a daunting task, it really does, but some things I did for my conversion using an EP82 loom/engine/ECU which may help you are... - Try to use as much of the EP91 loom as you can, all you should end up doing is chopping a few connectors (because they don't fit on the EP82 engine) and running a few extra wires to the ECU - Try to use your EP

i did think that bud. would have to extend the loom about 40cm due to where the ecu sits in the ep91. ill have a gander tonight

cheers bud. was hoping to have engine in by now but missus has been in hospital so been tied up with my boys more than usual lol. I've mated the fte upto my gearbox and is now under the car ready to be lifted in. whilst doing this i noticed that it has a paddle clutch installed so that is a huge bonus. should have it in over the weekend then ill be plugging in my 4efe loom where it fits, taking all the sleeves off the wiring and adding what connectors don't fit and also adding the few wires like knock sensor and new map sensor wire as on the 4efe the wire is shared in the loom. also t

just looks like the main part of the engine loom excluding lights. the lights side of things had the engine fuse box attached just boucht all the engine loom and ecu for my sr this one does have the igniter and map sensor attached which is a bonus

got pics bud but they no good tbh as everything's covered in insulation tape haha ill jot it all down over next couple of days, needs to come out tomorrow as its now sold so ill get some better pics and write down what wire goes where. theres only 6 wires to wire in so its pretty basic

haha bump strips will be going on Yeah mate not ideal but living in North Wales you soon get used to it lol. really could do with some better weather but hey ho, cant be driving this slow arse frontera much longer

Long shot but after a black SR bonnet May consider Glanza s but rather normal Taa

Managed to clean my bay today with some WD and rags. Also fitted ambers (had a few comment telling me to put some on) and much prefer how they look. Will eventually get the bump strips for the sides but I'll wait till its running again.

Managed to get the engine and box out today, they put sansors/connectors in the most awkward place on these things Going to spend tomorrow cleaning the bay and getting rid of any brackets I don't need. Also will mate the gearbox up to the 4efte. Have Monday and Tuesday off work so will take all the sleeves off the wiring and add the extra bits I need from the 4efte loom.

Any side exits for sale before I make one?

Yeah is a shame to sell, cheap buy for someone as you'll be able to turbo an NA for under £600. My build begins tomorrow

Bump. Will split