Chris_GlanzaV98 Posted November 3, 2013 Share Posted November 3, 2013 I painted the rear of my car a while back and it came out great but this time im wanting to go round all the seams and clear a bit of that crap they put round the joints/seams/welds to have it all smooth before my cage goes in when i get it I was going to tackle this with a drill and wire brush tool on the end but dont know if this will be too harsh and cause damage or take chunks out of it anyone, done this and if so how do you go about it ? With regards to the holes from rear trim and seats etc im wanting to smooth over them can this be done with catalloy or do they need to be welded ? My only consern with useing a filler is that it cracks as the car flexes and Moves Any help is appreciated and thanks in advance Quote Link to post Share on other sites
Chris_GlanzaV98 Posted November 4, 2013 Author Share Posted November 4, 2013 Anyone ? Quote Link to post Share on other sites
mikey4410 Posted November 4, 2013 Share Posted November 4, 2013 Dont know that removing factory sealant is advised,its there for reason.lol Quote Link to post Share on other sites
Chris_GlanzaV98 Posted November 4, 2013 Author Share Posted November 4, 2013 Not removing it just taking away the excess it wont be completely removed just smoother and tidier mate Quote Link to post Share on other sites
Patches Posted November 4, 2013 Share Posted November 4, 2013 JordanEP91 did this http://www.ukstarletowners.com/topic/67180-jords-v-300bhp-build/page-2?hl=seams#entry866464 10 posts down Quote Link to post Share on other sites
Patches Posted November 4, 2013 Share Posted November 4, 2013 ha just realised u commented on his build just down from that post Quote Link to post Share on other sites
Chris_GlanzaV98 Posted November 4, 2013 Author Share Posted November 4, 2013 haha cheers patches forgot about that mate, ill take a swatch Quote Link to post Share on other sites
Gainzy Posted November 4, 2013 Share Posted November 4, 2013 Wire brush would be too harsh I think just use a DA sander on the bits you can and handflat the rest as for the holes I can't see there been much flex for the filler to crack when I do mine eventually I will be leaving the holes but it's up to you Quote Link to post Share on other sites
Chris_GlanzaV98 Posted November 4, 2013 Author Share Posted November 4, 2013 Nice one mate cheers ill probs test both methods as jordan seemedto get on ok with the wire brush the rest will be hand sanded y Quote Link to post Share on other sites
Gainzy Posted November 4, 2013 Share Posted November 4, 2013 Basically don't get deep scratches in the metal or it will show up in the paint getting a clean smooth surface is what you want any bare metal just etch over for extra protection...what paint are you using and what colour? I wouldn't bother with the filler it's extra weight haha Quote Link to post Share on other sites
Chris_GlanzaV98 Posted November 5, 2013 Author Share Posted November 5, 2013 Most likely be rattle cans as i dont know anyone witg a spraygun and compressor but i got a good finish with it last time only this time im going a bit further with prep work, wire brush is on really for the excess goo stuff on the welds the rest will be hand sanded and then probs use etching primer just to make sure paint sticks maybe 2 coats of top and 2 clear ill document somePics Quote Link to post Share on other sites
Gainzy Posted November 5, 2013 Share Posted November 5, 2013 Ahh cool might be worth buying some panel wipe aswell get the surface as clean as you can to stop any reactions with the paint yes put some pics up on the way, good luck hope it turns out how you want it Quote Link to post Share on other sites
Chris_GlanzaV98 Posted November 5, 2013 Author Share Posted November 5, 2013 Sure gainzy no sweat kate ! Dont worry ill make a good job of it and a how to if it works if it doesnt workItll be a how not to:p Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.