5e colin Posted November 22, 2017 Share Posted November 22, 2017 Hey guys going to fit new guides but can't find it anywhere online could some link me please or get Toyota part nor cheeeers Quote Link to post Share on other sites
federalman Posted February 20, 2018 Share Posted February 20, 2018 I shall be keeping an eye on this thread for suggestions, going to replacing the ones in the Silvia at some stage Quote Link to post Share on other sites
Calum122 Posted February 20, 2018 Share Posted February 20, 2018 Yeah colin what did you find out in the end? Quote Link to post Share on other sites
5e colin Posted February 20, 2018 Author Share Posted February 20, 2018 I found that 1 from a ducato bike will work its only 0.5 mm undersize but pricey at 60£ still looking for cheaper if all fails I will make 1 out of a stock valve and get bush machined and welded on Quote Link to post Share on other sites
Rob H@RCH Engineering Posted February 21, 2018 Share Posted February 21, 2018 Your after something like this then Quote Link to post Share on other sites
5e colin Posted February 22, 2018 Author Share Posted February 22, 2018 Yes indeed rob that's it where did you get yours or is it d.I.y ? Quote Link to post Share on other sites
Rob H@RCH Engineering Posted February 22, 2018 Share Posted February 22, 2018 Its a diy one, I saw this post and thought I make one, I’m going to do one thats a depth stop for putting em in with too if needed Quote Link to post Share on other sites
Rob H@RCH Engineering Posted February 22, 2018 Share Posted February 22, 2018 There ya go a removal tool and setting tool to get them all to the correct depth Quote Link to post Share on other sites
5e colin Posted February 22, 2018 Author Share Posted February 22, 2018 Make me 1 please I will buy it of you think you could make a few as plenty would do there own guides Quote Link to post Share on other sites
Rob H@RCH Engineering Posted February 22, 2018 Share Posted February 22, 2018 Thats not a problem mate, I’ll give you a tip too knock the out from the block side and in from the top, also leave the new gides in the freezer over night before fitting them! Pm me Quote Link to post Share on other sites
5e colin Posted February 23, 2018 Author Share Posted February 23, 2018 13 hours ago, Rob H said: Thats not a problem mate, I’ll give you a tip too knock the out from the block side and in from the top, also leave the new gides in the freezer over night before fitting them! Pm me Thanks for that And thanks for the freezer tip Quote Link to post Share on other sites
maddox710 Posted February 23, 2018 Share Posted February 23, 2018 That looks smart Rob! Quote Link to post Share on other sites
maddox710 Posted February 23, 2018 Share Posted February 23, 2018 Also valve stem seal tool, not valve guide :p Quote Link to post Share on other sites
Rob H@RCH Engineering Posted February 23, 2018 Share Posted February 23, 2018 Cheers, the tool for fitting the guides also doubles up as a stem seal fitter too perfect! Quote Link to post Share on other sites
maddox710 Posted February 23, 2018 Share Posted February 23, 2018 1 minute ago, Rob H said: Cheers, the tool for fitting the guides also doubles up as a stem seal fitter too perfect! You wanna knock a few of them up and stick them up in the fs section sure you get a few people take them off your hands Quote Link to post Share on other sites
Rob H@RCH Engineering Posted February 23, 2018 Share Posted February 23, 2018 I’d rather make them to order tbh, I do make a few tools for stock but only the ones that sell well, these only take an hour or so to do anyway. Quote Link to post Share on other sites
5e colin Posted February 23, 2018 Author Share Posted February 23, 2018 I have an order in hi hi. Invoice me when your done Quote Link to post Share on other sites
Rob H@RCH Engineering Posted February 25, 2018 Share Posted February 25, 2018 (edited) I got 2 sets done today so I will PM you Colin and If any one else is interested fire me a pm or contact me through Facebook https://www.facebook.com/rchengineering/ Likes are always welcome too! Edited February 25, 2018 by Rob H Quote Link to post Share on other sites
Calum122 Posted February 25, 2018 Share Posted February 25, 2018 I may ping you an email some time Rob, this seems like a handy tool to have! Quote Link to post Share on other sites
Rob H@RCH Engineering Posted February 25, 2018 Share Posted February 25, 2018 2 minutes ago, Calum122 said: I may ping you an email some time Rob, this seems like a handy tool to have! That’s fine mate I will try to keep at least a set available all the time. Quote Link to post Share on other sites
5e colin Posted February 26, 2018 Author Share Posted February 26, 2018 pmed rob Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.