madmax_926 Posted May 4, 2010 Share Posted May 4, 2010 just won a ebay manifold for my ep91 was thinkin of buying a decat off there as well now i no these prob aint as good as sanc like j performance or on from ricky at ractech if it where to crack it aint gonna mess my car up ill prob just need a new 1 wont i? im only running 0.7 boost so should be ok if i fit a decat and mani does my car need a ecu if i run with standard ecu will it be ok the only mod performance wise is a hks actruator is it ok to fit the decat and mani?i hope u understand my rambling on? Quote Link to post Share on other sites
WallaceGlanza Posted May 4, 2010 Share Posted May 4, 2010 If you show us the one you bought we can actually see what it is!;)If it does crack it won't cause any problems other than a loss of power and a horrible noise, unless you're really unluky and a chunk falls off and kills the turbo.Finally yes a mani and decat will be fine at 0.7 bar, you only need to worry about the fuelling above 0.8bar Quote Link to post Share on other sites
madmax_926 Posted May 4, 2010 Author Share Posted May 4, 2010 If you show us the one you bought we can actually see what it is!;)If it does crack it won't cause any problems other than a loss of power and a horrible noise, unless you're really unluky and a chunk falls off and kills the turbo.Finally yes a mani and decat will be fine at 0.7 bar, you only need to worry about the fuelling above 0.8barthanks for swift reply so if i fit these parts it will be an instant power gain and the only thing to worry for is cracks so i can put these on tomorrow i dont have uprated air filter only actuator so it will be ok? and yeh boosting 0.7 will it creep the boost?? cause i can reset actuator Quote Link to post Share on other sites
iamlegend Posted May 4, 2010 Share Posted May 4, 2010 well wheres the mani then??? is it the autobahn shite?? if so yes it will be fine for couple days then blow up Quote Link to post Share on other sites
WallaceGlanza Posted May 4, 2010 Share Posted May 4, 2010 thanks for swift reply so if i fit these parts it will be an instant power gain and the only thing to worry for is cracks so i can put these on tomorrow i dont have uprated air filter only actuator so it will be ok? and yeh boosting 0.7 will it creep the boost?? cause i can reset actuatorIt'll be fine, you'll only find out whether it creeps after fitting it, there's no definite answer but yeah get em on! ;) Quote Link to post Share on other sites
madmax_926 Posted May 4, 2010 Author Share Posted May 4, 2010 well wheres the mani then??? is it the autobahn shite?? if so yes it will be fine for couple days then blow upthink its much worse than that but paid hardly n e thing for it take a lookhttp://cgi.ebay.co.uk/TOYOTA-STARLET-EP82-...282170529376162 Quote Link to post Share on other sites
durmz Posted May 4, 2010 Share Posted May 4, 2010 think its much worse than that but paid hardly n e thing for it take a lookhttp://cgi.ebay.co.uk/TOYOTA-STARLET-EP82-...282170529376162ohhh noooeesss!!! don do it mon! Quote Link to post Share on other sites
madmax_926 Posted May 4, 2010 Author Share Posted May 4, 2010 shall i get the decat cause my japspeed cat back arrives and might as well put it all on a? Quote Link to post Share on other sites
WallaceGlanza Posted May 4, 2010 Share Posted May 4, 2010 That won't last long. Quote Link to post Share on other sites
madmax_926 Posted May 4, 2010 Author Share Posted May 4, 2010 ok mate well at 0.7 should last a while shouldn it or does boost pressure have nanc to do with it? Quote Link to post Share on other sites
durmz Posted May 4, 2010 Share Posted May 4, 2010 ok mate well at 0.7 should last a while shouldn it or does boost pressure have nanc to do with it?boost pressure has a bit to do with it, but seriously man them manifolds are terrible, it really wont last five minutes Quote Link to post Share on other sites
lukerobz Posted May 4, 2010 Share Posted May 4, 2010 my mate had a stainless steel mani it kept crackin load off crap he sees Quote Link to post Share on other sites
daz gt turbz Posted May 4, 2010 Share Posted May 4, 2010 make sure you get a braced de-cat, i got them and the mani lasted about 8months then it totaly shat itself, it cracked nearly all the way round the turbo flange on the weld and on the way home(driving very steady) because it was moving loads it cracked the oil feed pipe to the turbo, which left me on the side of the road waiting for my mate with a trailer. so although it may have been cheap it might not be so cheap in the future! Quote Link to post Share on other sites
Carl. Posted May 4, 2010 Share Posted May 4, 2010 those mani's have 1.3mm thick runners ;) i wouldnt bother fitting it mate its just gonna piss you off WHEN it cracks. Quote Link to post Share on other sites
Carl. Posted May 4, 2010 Share Posted May 4, 2010 and its not just a 5 minute job to swap it back Quote Link to post Share on other sites
whiteglanzav Posted May 4, 2010 Share Posted May 4, 2010 those mani's have 1.3mm thick runners ;) i wouldnt bother fitting it mate its just gonna piss you off WHEN it cracks.DO NOT fit that manifold lol - sell it on ebay and buy a propper 1 Quote Link to post Share on other sites
Raz Posted May 4, 2010 Share Posted May 4, 2010 LOL the best Mani ever do they still get made LOL? Quote Link to post Share on other sites
Carl. Posted May 4, 2010 Share Posted May 4, 2010 LOL the best Mani ever do they still get made LOL?yeah mate but they are soooooooooo rare they are only available on the bay of E.... FACT!!! ;) Quote Link to post Share on other sites
Raz Posted May 4, 2010 Share Posted May 4, 2010 Mate, Don't fit the mani! It will cause you problems and possibly blow your turbo. Quote Link to post Share on other sites
guy86 Posted May 5, 2010 Share Posted May 5, 2010 i had one and it lasted a week!!! complete shit!!! buy a zisco they r the doggys ball bags!! Quote Link to post Share on other sites
madmax_926 Posted May 5, 2010 Author Share Posted May 5, 2010 ok people well fair ones ill take your advice and get it sold thanks! sowot about j performance? Quote Link to post Share on other sites
micky boy Posted May 5, 2010 Share Posted May 5, 2010 Jperformance decats and intercoolers are good enuf for the job as for the manifolds (SHIT) dont bother like people have said get a Zisco one Quote Link to post Share on other sites
durmz Posted May 5, 2010 Share Posted May 5, 2010 Basically stainless manifolds are generally shite unless u spend a bit of dough on better grade steel, ie the sort of thickness and quality ricky lee uses is his stuff, and zisco use. Budget wise mild steel is the best bet Quote Link to post Share on other sites
madmax_926 Posted May 5, 2010 Author Share Posted May 5, 2010 ok so ricky sells some good stuff and so does zisco is there a website for zisco Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.