Help needed!

[Charlie28]

Can anyone just help me out with a few little bits please!

Firstly, what plugs into the head here? And does anyone have it spare?

Secondly, what plugs onto this and where does it go?

And lastly, I have an older spec engine in my 98 glanza and I don't seem to have a connection on the loom to connect to this? What is it and is it required?

[GlanzaJim]

The middle pic is a vac goes somewhere, but the.last one dont worry about it. I didnt have it on my loom but was on engine. Like a like earth. Didnt affect the car.

[FMuscle]

First pic:

One goes to the throttle body, the other to the canister under the fuel filter.

Second pic, I can't help just from the pic, I can't figure where it is exactly on the engine...

Third, as Jim said, don't worry. just leave it there to block the hole.

Edited December 21, 2014 by FMuscle

[Charlie28]

It's on the back of the inlet bud.

Cheers for the help on the others

[Charlie28]

Don't suppose you have any better pics of the pipe that goes to the throttle body?

[glanzatd04l220]

It's on the back of the inlet bud.

Cheers for the help on the others

not 100% sure but think it goes to your map sensor.

kevin

[Charlie28]

Anyone got the pipe that goes to the throttle body for sale?

[Charlie28]

Scrap that. Found out it's for the A/C and isn't required.

[Ryan5793]

little one on the inlet i had 2 of these both sides on the back and was told to block them off so just connected them both together for the time being and seems ok lol

[FMuscle]

As mentionned before, my first thought would be the MAP sensor, or if you already have one there, block it off.

This is what I have for the 2 off the coolant housing:

[FMuscle]

Would you mind sharing your findings on this? I don't have A/C anymore, I'm interested...

Scrap that. Found out it's for the A/C and isn't required.

by the way I have a broken one if you're just looking to fill the hole. I'm a bit far tho, but if you're not in a rush I can send it for postage.

Edited December 22, 2014 by FMuscle

[Charlie28]

Thanks for the help guys!

What I forgot to mention is this is a GT engine in my glanza.

I believe it's a temp sensor for the A/C but on a glanza this is built into the main thermostat sensor making it a 3 prong connection.

I've bought a sensor now just to plug the hole

[RobSR]

First pic:

One goes to the throttle body, the other to the canister under the fuel filter.

Second pic, I can't help just from the pic, I can't figure where it is exactly on the engine...

Third, as Jim said, don't worry. just leave it there to block the hole.

Mate thats an N/A engine. Charlie is asking about an FTE.

The spare port is for a temp sensor GT's used. Glanzas don't have it so block it off.

[corofin12345]

1st pic - blank it off or use a broken sensor in it etc

2nd pic - not needed but block it off.. small piece of vac hose and a bolt will do

3rd pic - sensor not needed but leave it as is (old temp needle sensor).. on that housing.. the CTS normally has a 2 pin sensor and a separate loom for the temp needle sensor ... uve replaced that sensor with a 3 pin sensor by the looks of things to suit your loom (3rd pin on CTS is temp needle sensor)

Edited December 23, 2014 by corofin12345

[Charlie28]

1st pic - blank it off or use a broken sensor in it etc

2nd pic - not needed but block it off.. small piece of vac hose and a bolt will do

3rd pic - sensor not needed but leave it as is (old temp needle sensor).. on that housing.. the CTS normally has a 2 pin sensor and a separate loom for the temp needle sensor ... uve replaced that sensor with a 3 pin sensor by the looks of things to suit your loom (3rd pin on CTS is temp needle sensor)

Perfect mate! Thank you