aaddzz123

!!

Just in the layby mate. It'll be in the one headed towards the big island...

Jeez no need to go on and on about it lol! You'll see what game I'm on about. BITCH! You know that I will beat you at any game... Any game at all in the whole arcade, I will beat you at.... Without a doubt.... also, don't mind picking you up. Will let you know tomorrow what time.. When you free? also, don't mind picking you up. Will let you know tomorrow what time.. When you free?

BOOM! Result ha! I want this spec sheet to work though! I'm excited lol

Yeah Neil, Nile, josh, fred whatever! lol Tenpin bowling then? Anyone? Lottie you can shotgun with me if you like. I have no idea where it is and I wanna kick your fucking ass at the mini game!

If you wanna learn, give it a go. If you just want a good finish take it to someone that knows what they're doing... It could take you 50 trys to get it spot on and by that time you could have spend ££££ on supplies lol.... But off the top of my head!... Right! First of all you need to rough up the area plus about 6 inches to 12 inches past where you're not going to paint. Use a scotch pad or 800 wet n dry paper. Then its time to get the panel nice and smooth. You can do that by using filler and high build primer. Its a boring task getting a smooth surfance but it pays off big time in the end result if you put more time into the prep work. My biggest tip here would be to use a sanding sponge! Keep your pressure even and do long strokes... You don't want a rippley panel... You may have to do several coats of high build primer before you stop seeing high and low patches in the primer... When its completely smooth, go over it with 800 wet and dry paper (wet) to get it ready for paint... Bare in mind that the above could take you days on your first try. Don't settle for anything less than perfect! Everything is visible in the end if you don't do it right at the start... When you're happy with the affected area, you can get your paint ready. To be honest, with such a small area, I'd just get paint mixed in a rattle can with a decent nozzle. It can take a long time to get a decent set up on the compressor and gun and if you get it wrong, you would find yourself back at stage 1 sanding it all down again... You want to paint the area evenly and build layers up. Don't just go blasting it on. Do a very light dust coat to begin with and let it dry for say 15-20 seconds. And then start building your layers up. You want to make sure you cover all the primer but stay within the area that you roughed up (Those extra 6-12") Finally when its completely covered, hold the can/gun further away from the car and kinda "brush" the paint in at the edges to get your blend... I personally find it as easy as it sounds lol. Some people say its hard I guess practice makes perfect... Remember you still need to stay within that exta area that you roughed up... If need be, you can always rough it up a little further (Its just to help the paint stick... Paint doesn't stick too kindly to anything shiney!) When you're happy with your blend you can add a clear coat (Providing you didn't use a 2k paint in the gun in the first palce). You're going to want to use a 2k clear coat and hardener for this bit without a doubt... Please please read up on 2k paints before you start using them. Ideally you need an air fed mask to use it. However, I'm a retard and just use a high end respirator and big goofy goggles... When you're doing this, try and go as near the end of the rough area as you can. Make sure you're giving it light even coats and build up the clear. Don't worry if its cloudly and patchy as fuck after the first coat, it all merges and "melts" together. Wait about 30-60 seconds between each layer and keep going evenly until you have a nice smooth shiney finish.... Don't go past the rough area remember! When you've finished that, mix the rest of that clear coat that you have left in your gun to about a 1/10 ratio with thinners (what you have, x10 in thinners), Stir well and just brush out the edges of the clear coat to blend it in the best you can... When it's dry (give it a week), hopfully it will look clean and realitively smooth... Now you can flatten it down with 1500 wet and dry paper (again using the sponge) and then use compound cutter and a good polish to bring out the real shine... Bare in mind I'm not a pro... I've been doing bits of bodywork for years and know what I know from trial and error... Theres a lot of time and effort that goes into bodywork, you need to take your time and be careful of your health! 2k is nasty shit lol! Remember to use wax and grease remover between coats... Don't want fish eyes! All of this is just off the top of my head.. I've probably missed 1 or 2 vital bits of information so if you're gonna do it, only use this as a rough guide lol. Might be worth getting a few books on it or watching some videos online... Loads of information out there to get started.... Its hard work though. Be prepared lol!

Tut! Haha ... Ok erm... We could just go... I don't even know lol! What about bowling or somthing? What was that place that we went lottie? With Liam n your mate, can't remember his name lol... Basically a little arcade/bowling place. It does have a bar but its only one side... Rest is just games and bowling?

I'll be there ... There are a few places but not many with cover lol... It was hailing earlier but sun came out for a bit after... Sky is full of black clouds again though lol! The shit I've had to put up with recently is insane.... How about we go to a pub or something? Could all go to where we had the last meet near Lottie's house... Hopfully it won't be raining lol

BOOM! Sex wee What did it have done in the end? They work fast lol

Lmao at the havock I'm causing on this thread lol! Sorry guys... Certain parts have been a fucking pain in the arse :/

Haha! Yeah but it really is the dogs! I'm currently saving awesome for full 1080p hd filming ;)... If you want crisp pictures and loads of adjustablility, you're gonna have to go for an SLR really. So many lenses,manual settings etc... Saying that I've used a lumix compact for years and it's done me well. Nothing special at all though... Get on ebay. Not be able to get one for less than £200 I imagine

Canon 60D.... That is all.

"Slammed" haha Bringing back the old manny sayings ! We want before and after pictures Just so everyone kows, "slammed" around our neck of the woods has always just been another word for "lowered"... Doesn't necessarily mean it's on it's bum hole!

Same ^^^ AWESOME!

Haha! Heres me trying to be all secretive with updates and you're posting it on here anyway lol! . I've got a few more pictures ;) Will upload in a mo for you mate

Awesome mate! If you look at bidding on ebay too you can get them pretty cheap. Mine cost about £150 lol! Brand new... This one is with td04 and screamer, but still with japspeed exhaust so...

Don't quit before you get a new job for 100% deffinate... I've been jobless since December and I've had to resort to doing full time car bodywork in my nan's garage just to pay for basic shit :/ Not a good place to be

LIKE I'll pay for my tickets as soon as I have some pennies lol!

Shall we jsut say that John wins this month and start posting pictures for next month? lol! And thanks mate! I think it looks gash though lol! Can't wait to paint it next week along with my refurbed rims ;)

:surrender: I'll be there whenever lol! I reckon Wednesday

Get my ugly mut in there haha! Rude Boi

I have a load to share! Let me get uploading now. Will post in next half hour or so!

lmao I've been told about this!! I was recommended to watch it several times just to witness how bad it really was. Haven't seen it yet... Gives me an idea actually... JAE, anyone got a projector we could hook up and play films onto the marquee wall later in the night when we're all fucked? Something like this would be a good laugh

.