Ryan_EP82 GT Posted June 3, 2013 Author Share Posted June 3, 2013 A fresh 4EFTE is usually the easier route. In terms of time, effort and budget a rebuild might not be your ideal solution. It's a days work instead of a weeks work. Costly lesson unfortunately mate. Unfortunately its just one of those things, but it does seem to be one after another. Awk well, shit happens, thanks for the advice again Jay,Chris,Amjad! Quote Link to post Share on other sites
Jhandy Posted June 4, 2013 Share Posted June 4, 2013 I rebuilt my engine last year and cost me 304 quid. I rehoned it myself got some second hand pistons. Brand new rings and bearings from Toyota. And a head set from euro car parts for 85 quid. Don't take that long either bud Quote Link to post Share on other sites
Ryan_EP82 GT Posted June 6, 2013 Author Share Posted June 6, 2013 nice one man you didnt do bad at all, in fairness i couldnt do any of the work myself so it would cost a brave bit more id say. im gonna try replace the engine to get boosting again asap and forge the old one next year. i think a sunny holiday comes before the engine lol Quote Link to post Share on other sites
Ryan_EP82 GT Posted July 8, 2013 Author Share Posted July 8, 2013 (edited) ' Edited September 30, 2013 by Ryan_EP82 GT Quote Link to post Share on other sites
Ryan_EP82 GT Posted October 28, 2013 Author Share Posted October 28, 2013 (edited) So we got to the root of the problem anyway, turns out a wrongly configured FPR led to the engine overfuelling and destroying the ringlands Costly lesson indeed and after some favours and a bit of saving the GT is back and running on the road Firstly, i got myself a full Toyota engine gasket set from Idrees and had every gasket and seal replaced and a new Toyota PCV valve as well.. Then we got the head sent off to be pressure tested, skimmed and fitted with new Toyota Valve stem oil seals. Came back like this: Things were going good but that was the end of the progress for a load of months due to a lack of funding! But another student loan came in, and went straight out again on the Starlet lol. The bottom-end was sent off to be rebuilt by Byre reconditioning. I got the block pressure tested.. bores honed and washed, ACL bearings and washers fitted, and pistons with new Toyota piston rings installed. Component list fitted:-ACL Big-end bearings-ACL Main bearings-ACL Thrust washers-Genuine Toyota piston rings-New timing belt & tensioner kit 4 cracking pistons from another Gt Turbo cleaned up and ready to be fitted with the Toyota rings The engine was torqued according to Toyota specs the head fitted with new Toyota head-bolts Just waiting on the paint to dry on the cam cover and in it goes! Edited November 5, 2013 by Ryan_EP82 GT Quote Link to post Share on other sites
daniel_g Posted October 28, 2013 Share Posted October 28, 2013 Glad you got it all sorted Ryan !! Quote Link to post Share on other sites
Ryan_EP82 GT Posted October 28, 2013 Author Share Posted October 28, 2013 (edited) Managed to swap a few turbos and bits an bobs, got myself a Roadrunner manifold that had a bit of an ugly weld thrown up the middle and ported it out it with a Dremel and mock exhaust gasket before fitting Searched and found, thanks to Browners stash as usual lol, a matching Roadrunner twin-pipe decat It's supposed to seperate the exhaust gas and wastegate gas to improve air flow. This is them both installed as a mock up before the engine was fitted.. Edited November 5, 2013 by Ryan_EP82 GT Quote Link to post Share on other sites
Ryan_EP82 GT Posted October 28, 2013 Author Share Posted October 28, 2013 Glad you got it all sorted Ryan !! thanks alot mate.. i genuinely missed the little thing! i cant wait to get a drive in it again Quote Link to post Share on other sites
Ryan_EP82 GT Posted October 28, 2013 Author Share Posted October 28, 2013 (edited) Found an oem Toyota rear strut too I got a few genuine Toyota oil filters over time and Millers competition 10w40 mineral oil for bedding in We painted the rocker cover since it was off anyway and tried to somewhat resemble the Magnecore blue lol THE FPR HAS SINCE BEEN REMOVED/DESTRYOED!! Edited October 28, 2013 by Ryan_EP82 GT Quote Link to post Share on other sites
Ryan_EP82 GT Posted October 28, 2013 Author Share Posted October 28, 2013 (edited) Now that its home it needed tidied up a bit to prepare for mot.. Edited October 28, 2013 by Ryan_EP82 GT Quote Link to post Share on other sites
Darraghmh91 Posted October 29, 2013 Share Posted October 29, 2013 Nice one man looks pretty clean . How do ya reckin youl get on for the mot Quote Link to post Share on other sites
Ryan_EP82 GT Posted October 29, 2013 Author Share Posted October 29, 2013 Nice one man looks pretty clean . How do ya reckin youl get on for the mot Thanks mate, didnt expect to have to rebuild it so soon but thats life, and here i am.. I think iive a few bits just, wheel an headlight alignment, new clutch slave cylinder, and getting hold of a battery to send it through. I dont think they'll appreciate me holding down an 063 battery with a bungee cord!lol Quote Link to post Share on other sites
Darraghmh91 Posted October 29, 2013 Share Posted October 29, 2013 Atleast its done man its a fresh engine now so its peace in mind for you now .. Ahh thats ok nothin major to be done anyways then but yeah a few eye brows would be raised if you sent it in with you holdin it down haha they might fail it for bein unsafe haha talk about being too strict haha :-p Quote Link to post Share on other sites
Ryan_EP82 GT Posted October 29, 2013 Author Share Posted October 29, 2013 Thats it bud nothing beats peace of mind! Do it once, do it right an all that except for bungee cords!! i stick by them...lol.I need to get it on the rolling road once its back up to a higher boost again, im dying to see how healthy the engine is and it would be interesting to see what its putting out at stock boost pressure Quote Link to post Share on other sites
Darraghmh91 Posted October 30, 2013 Share Posted October 30, 2013 Is the car still standard like ct9 standard boost . If so id say youd be gettin about one30 . When do you hope on gettin a dyno Quote Link to post Share on other sites
Ryan_EP82 GT Posted October 30, 2013 Author Share Posted October 30, 2013 I was running .8bar with a few minor mods before the bottom end went, nothing too extreme until I get an emanage or piggyback ecu to sort the fuelling proper. I'd like to see close to 200 eventually, that's my goal for around xmas time...Once I get it back to that boost I'll bring it to Autotune in ballymena and get them to RR it there. Quote Link to post Share on other sites
Darraghmh91 Posted October 30, 2013 Share Posted October 30, 2013 Go for a stand alone man them piggybacks are ment to be shite Would you get a ct9 hybrid man not a lot of lag and good to go aswell and dont empty the pocket either ha When umi have the car the way i want it im gonna get a gt28 kit so will be up near 350 bhp Quote Link to post Share on other sites
Ryan_EP82 GT Posted October 30, 2013 Author Share Posted October 30, 2013 Go ahead lad!! Gt28's are mental..lol I call shotgun for a blast when you have it fitted. I was hoping for a good Tongs hybrid but I think I might try make my own with a ct12 exhaust housing and ct9b impeller,unsure about the exhaust wheel yet :/ means minimal lag/roughly same spool but with a few extra horses top-end. What hybrid you running bud? Quote Link to post Share on other sites
Ryan_EP82 GT Posted October 30, 2013 Author Share Posted October 30, 2013 I was hoping to go for a Mine's or Jam, have you had any experience with those lad? Quote Link to post Share on other sites
Darraghmh91 Posted October 30, 2013 Share Posted October 30, 2013 (edited) yeah would be pretty nice man but its like 2500e so ill be a while savin for it but itl be worth it then forge the engine and wiseco pistons pauter rods etc I've heard loads of great reports about haltech manbut there pricy to buy.. but to be fair you pay for what you get no point gettin a cheap ecu and its blows on ya nano who ever your join to map the car you should ask them a good ecu .. I've never had any dealings with mines or jam but ill ask a few lads who have and see what feedback i get for you be a great achievement to do up your own turbo man and as far as i know its a thongs hybrid Edited October 30, 2013 by Darraghmh91 Quote Link to post Share on other sites
Ryan_EP82 GT Posted October 31, 2013 Author Share Posted October 31, 2013 (edited) yeah it dont be long totalling up bud i thought about going forged but i couldnt staying off the road any longer to save. haha.. id prefer to have the ep85 4wd i think before i put Garrett turbos near it!lol have you looked into the 5e conversion yet or you staying with the 4e? yea if you get any feedback let us know that would be great, cheers!! an your right there pal, you get what you pay for so best off going all out at it once. Lol, a friend of mine swears by this Megajolt ecu, i havent heard of anyone using them before have you? obviously id need to send it off to get balanced an that but i wouldnt mind designing my own.. haha..Tongs would be my sole choice otherwise they are meant to be a great turbo, does it pull til redline?? Edited October 31, 2013 by Ryan_EP82 GT Quote Link to post Share on other sites
Darraghmh91 Posted October 31, 2013 Share Posted October 31, 2013 Yeah its a pretty expencive hob y gettin all fancy turbos ha theres a lot more than others think like just forgin it is a bomb then you have to get all the rest to go along with it ha fuckin nightmare ha but great resultYeah ill let you know and I've never heard of anyone usin thdm but they could be good man No it looses power man im not drivin it at the minute im drivin the gi Quote Link to post Share on other sites
Ryan_EP82 GT Posted November 16, 2013 Author Share Posted November 16, 2013 (edited) Yeah its a pretty expencive hob y gettin all fancy turbos ha theres a lot more than others think like just forgin it is a bomb then you have to get all the rest to go along with it ha fuckin nightmare ha but great resultYeah ill let you know and I've never heard of anyone usin thdm but they could be good manNo it looses power man im not drivin it at the minute im drivin the gi yeah it adds up alrite man ends up a fortune, i priced it before i built it stock just took one lock and turned that idea off lol...Someday!! Update.. Car seems to be running well ..piston rings are bedded in well, did a good 140mile round trip there, i threw £15 petrol in too so that wasnt bad atall Feels amazingggg to be back in GT Edited December 3, 2013 by Ryan_EP82 GT Quote Link to post Share on other sites
Ryan_EP82 GT Posted December 27, 2013 Author Share Posted December 27, 2013 (edited) Not much of an update but got some more jdm bits to go in now - HKS turbo timer to be fitted along with a hks harness. Weathers too shitty to get near the car to work though! Edited December 27, 2013 by Ryan_EP82 GT Quote Link to post Share on other sites
Ryan_EP82 GT Posted December 27, 2013 Author Share Posted December 27, 2013 (edited) . Edited December 27, 2013 by Ryan_EP82 GT Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.