Jump to content

Recommended Posts

  • Replies 1k
  • Created
  • Last Reply

Top Posters In This Topic

Done a couple of other things today :) nothing much!

Fitted throttle cable bracket :)

IMAG1078_zps7b8095dc.jpg

Fitted fuel filter :)

IMAG1079_zps329eecce.jpg

I painted this blue a while back, repainted it black and fitted

IMAG1080_zps292adf1c.jpg

Servo fitted and started to fit the abs removal kit can't fit the rest till I get my master cylinders back :)

IMAG1081_zpscd467760.jpg

Link to post
Share on other sites

Lol :p ^

But seriously i cant wait for this to finish, similar things are hapening with mine

Over winter with bay interior and exterior if all goes to plan :)

Love this, like i said before attention to detail is epic !

Hahah I was in my element with other things ;) that's why it upside down ;)

And me mate I want it finished :) good to hear someone's doing it the right way ;)

Thanks mate the hard work should pay off :)

Link to post
Share on other sites

Been doing some more work on the car today :)

Got some more stuff back today :)

Rear bumper

IMAG1083_zpsc8d5816a.jpg

Front bumper

IMAG1084_zpsa67bc26e.jpg

Also got my mirrors and side skirts back :)

Rear bumper fitted :)

IMAG1085_zps54d51fdd.jpg

Mirrors refitted :)

IMAG1088_zps0dc97369.jpg

IMAG1091_zps3100dece.jpg

Excuse the dust ;)

Refitted chassis plate :)

IMAG1089_zps63314a21.jpg

Fitted my fogs to the bumper :D

IMAG1092_zps9dc11a3a.jpg

Fitted this powdercoated cross bar :)

IMAG1093_zps86346900.jpg

With new bolts

IMAG1094_zps994024de.jpg

Put the bumper on, I know it has to come back off but it's safer on the car than in the garage because it may get knocked :)

IMAG1098_zps78967ac0.jpg

All new screws ;)

IMAG1097_zps49e025dd.jpg

Fitted the side skirts :)

IMAG1100_zpsf70bb871.jpg

IMAG1104_zpsa04f54c4.jpg

Again with more new screws :)

IMAG1103_zps441b7a87.jpg

IMAG1104_zpsa04f54c4.jpg

Just missing something now :)

IMAG1106_zps8644bf5e.jpg

Link to post
Share on other sites

One step further mate but wont the wings and side skirts have to come back off to put the engine loom back in?

:) I have never taken the wings off mate but I know what you mean :) let's see but need to then I will :) going to have the fuse moved behind the dash sometime too :D get the engine in and see what happens

Why would need to take the side skirts off?

Link to post
Share on other sites

Side skirts of to remove the wings... by the way dont put your fuse box in the dash its pointless. Idrees did it and it was a bitch to change a fuse and apparently it takes aaaaaages

Edited by Aamir
Link to post
Share on other sites

Ah right yeah my bad mate. And make sure you dont short any wires as thats what Idrees did and thats the reason why he stripped the yellow one because he went through all the effort of wire tucking and it wasn't worth it at all

Link to post
Share on other sites

Bloody hell mate I won't be doing it hahah, I know a guy who said he could sort it for me :)

I wouldn't dare attempting it, the car would never run again lol

Don't get me wrong I don't mind a few wires being on show but the main reason is because there are everywhere, I know you can tidy it up but it will annoy me knowing the wires are a right mess :)

Edited by JordanEP91
Link to post
Share on other sites

That's a mean looking photo of the front end.

Can I ask where have you gotten all these new bolts from ?

I thought the same thing mate ;)

These are all the original nuts and bolts that were on the car just had them zinc coated bud :)

Link to post
Share on other sites

Done abit more today :)

Removed the fuel tank :)

IMAG1140_zpsa8f8d7bf.jpg

I can now paint all behind it ;)

Fuel pump removed :)

IMAG1145_zps60e8cbfa.jpg

The tank is now ready to be powdercoated ;) was going to go blue the same as my rear beam and that but I might go for an orange or something brighten it up a tad :)

Link to post
Share on other sites

Honeslty buddy if I get 50% of your attention to detail on my shell next year il be a happy man.

Keep up the good work and can't wait to see this thing as shows

Thanks mate :) I'm sure you will do a good job you have so far :) yeah no doubt you will see it somewhere bud ;)

Just gets better and better jordan , Loving this build dude

Keep up the good work pal :thumbsup:

That's good to here boss :) yours is just keeps getting better and better too ;) I will bud :)

Fitted the engine mount bush tonight :)

IMAG1148_zps22259e82.jpg

Not bolted down yet

Also fitted a bracket on the inlet :) as I said before the inlet isn't going to be on there for long but it will done for the minuet :)

IMAG1149_zpsbe4bdb1e.jpg

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...