Duduglanza

450cc without fuel managment of some type.. will have you car run rich. if atill using a stantard ecu with fcd .. just go for 360cc.

My sidelamps and cluster are lighting up when pressing the brake pedal? any suggestions what should i check? Removing fuse12 and still getting lights on. I removed cluster and shaked al cables and wires to see if there is shorted wires but none worked. im clueless now

Fp and B+ should turn on the pump with ignition on.

Hi, I have some curiosty about knock sensor fault codes. Suppose you have a good knock sensor and its wiring... what fault code should we get when the engine knocks? 52 is only for no signal.. 53 and 55 are KS related but i cannot find reasons of faults. Thanks

Yeah for my emanage ultimate

Glad you sorted it out mate.

wanna do it too. need info

Need info. i want to use a variable tps on mine too. any diagrams or info i much appreciated. FB messenger me : Kyle Falzon

High idle is surely a leak or some sort of " extra " air passing through the throttlebody. try and remove intercooler pipe and block the inlet with your hand. the car should stall. if not its a leak. Give a quick check to your idle control valve too. might got jammed open

emanage ultimate. Got An injector adaptor on it that includes resisitors is in it too... hence i thinks thats the reason i didnt fry the injector drives. When chekcing resistance on the adapter got 500ohms on each wire. Guess they are in serious tough.

Hi, i have a question regarding resistor packs. what is the right resistor for 550cc 2.4ohm ( low impedance ) injectors? i got my rc 550cc injectors jn my hand and got two resistors that when tested for resistance its showing 1.2ohm each. can i use them or no? need a electric guru here

Hi mate , the question wasn t on lag time and injector size .

Hi guys, anyonr can give me more info on logging the injector duty cycle? there is input and ouput duty cycles. what should the numbers be on the two of them. i know that over 80% the "limit" but which one has to be 80 input or output? Thanks

Hi , As you all know the 4efte ecu has only 2 output channels for the injector pulses. 1&3 and 2&4. May I ask where is the part where the 2 wires split into 4? i need to fit two resistors on them for my low impedance injectors. Thanks

yeah im will run them with the emu. So i just find the power wire on the injector harness .. cut and put the resistors in between? Thanks

hi guys. I bought a set of Rc 550cc low impedance with a resistor box from another guy. The resistor pack has only 2 resistors. Which way should i connect them to the injectors? thanks

Is it on a gt or glanza mate?

I dont run one as i have an aftermarket intake. Bit still was fine before

Im getting a huge rpm spike when the fan kicks in or i flicker the bright on the headlamps. The rpm goes down from 1000rpm to nearly stalling the engine. Infact sometimes it stalls. Checked the alternator is working.. showing 14v stable. Any other things i can check?

Thanks for the help

Tought that below 20psi is a bit risky :/

Hi , im getting low oil pressure on idle.. 15/18psi when fully warm. Im a bit worried and i don't know much was this problem going on as i installed the aem oil pressure gauge few months ago and was always like this since then. Changed the oil relief valve but still same readings. Should I replace the pump for safety or can i add some washers in the oil relief valve just to increase the pressure by few psi? Anyone did this procedure?

That makes sense. Once i had the black wire from the plug behind the gauge that came out and tried to push it back in. Sometimes ut comes looae and the gauge turns off.. maybe ill arange that problem properly abd check again. Thanks

I had my Aem A/f meter for years now. Never replaced the sensor. I have the emanage ultimate on my ep91 and recently i data logged some pulls and noticed that the afrs oscillated a lot , not showing same on the display. So i stopped to check if the aem display and on my pc matched. On idle the display shows idling 14.7 steady but on the pc ( emanage ) oscillating from 13.1 to 15 rapidly. I know that i need to allow .1 or .2 but not that much. Is that the sensor or the gauge problem? Im using the white wire by the way 0-5 v and set the emanage from 10 - 20

Yeah thanks for the interest. Dont get me wrong hehe.. i use my car for street use aswell so i need best of both worlds.