Harrychambers21 Posted November 23, 2017 Share Posted November 23, 2017 so ive not a turbo 4EFE just wired up the det 3 ecu and i cant get the ignition adjust to work. ive got the link for my pin out and when i cut pin 6-igt and wire the det 3 for igt in and igt out it wont start. ive tried all different setting etc on det 3 and nothing helps. i can get rpm read out when i wire just the ignition in wire to pin 6 but i cant adjust it. any one know about the ecu det 3? cut map wire and connected the det 3 to that and adjusting fuel works fine just the ignition side ive tried all sorts. any help would be good. thanks Quote Link to post Share on other sites
Ollieh17 Posted November 23, 2017 Share Posted November 23, 2017 Had a similar thing with my emanage. Ignition wire was meant to be spliced into not cut Quote Link to post Share on other sites
leonidas127 Posted April 11, 2021 Share Posted April 11, 2021 Hey guys. Can you help about the full pinout ? I'm talking about det 3 on 4efe Quote Link to post Share on other sites
richardc9052 Posted April 11, 2021 Share Posted April 11, 2021 Cut pin 6 (IGT) on Connector 1 Cut pin 4 (PIM) on connector 1 Det 3 ignition IN goes to the ECU side of the IGT wire Det 3 ignition OUT goes to Engine side of the IGT wire Det3 Analogue IN 1 goes to Engine side of PIM wire. Det3 Analogue OUT goes to the ECU side of the PIM wire. Then just connect switched power and earth to the DET 3. Your done. Quote Link to post Share on other sites
richardc9052 Posted April 11, 2021 Share Posted April 11, 2021 You need to setup the config on the DET3 for it to run. Single Wire Retard will be used for ignition setting. Quote Link to post Share on other sites
leonidas127 Posted April 12, 2021 Share Posted April 12, 2021 thank you very much ! another question . will the 2 step function of the det 3 work alright with the 4efe? Quote Link to post Share on other sites
leonidas127 Posted April 12, 2021 Share Posted April 12, 2021 setup the config? doesnt it have a base map? explain me pls about the single wire retard cause my english are bad Quote Link to post Share on other sites
richardc9052 Posted April 12, 2021 Share Posted April 12, 2021 Yes it will work you just need to setup and pinouta switch or button for activation. They don't come with a base map. They come completely blank. If you don't know or understand that your best off bringing it to a tuner. If your adamant on doing this yourself then your going to have to hit Google and YouTube along with the Ecumaster manual. It's full on useful information. Quote Link to post Share on other sites
leonidas127 Posted April 13, 2021 Share Posted April 13, 2021 "Some more questions" Yes i ll try to do it by myself, I want my car to run like stock, i dont want it to make more power So i will have to make the fuel tables and the ignition tables, right? what others i ll need to adjust ? For adjusting fuel tables i ll need a wideband? Quote Link to post Share on other sites
richardc9052 Posted April 13, 2021 Share Posted April 13, 2021 If you want to keep it standard you can leave the fuel and ignition tables at 0. Just setup the configuration for inputs, outputs and ignition Quote Link to post Share on other sites
Frankieflowers Posted May 19, 2022 Share Posted May 19, 2022 Hi guys. I have to setup a DET 3 on a 4efte engine. Can someone help me with the fte ECU pinoit to the DET 3? @Claymore @Sam44 @RoyalDutchie Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.