GAZ@A&G_TUNING Posted November 29, 2008 Share Posted November 29, 2008 right mde up a new thread as when i sorted out my photobucket into folders it has got rid of the pics of here ;) Bought a 4wd starlet of ebay for 640 quid with plans to strip it all back and make it a gt replica but going fully forged and 1.5 blocki swapped my white gt which was td04 lsd etc with a mate for his not so good looking gtJUST A LOAD OF PIC'S OF STRIPPING DOWN AND SWAPPING BITS OVERDONOR CARLOVELY BROWN DASH IF ANY WANTS IT:pGEARBOX CLEANED UPBUMPER CUT OUT, DASH SWAPPED AND COMPLETE LOOM5E engine stripped down and forgedwhats better than one fully forged 5e engine? 2 fully forged 5e engines:p Quote Link to post Share on other sites
GAZ@A&G_TUNING Posted November 29, 2008 Author Share Posted November 29, 2008 body worksome first pics of it outsideafter running it it for a few miles, it got mapped at engine advateges made 240 at 1 bar hen when started to turn the boost up it started to det like mad, could of been a few things, after doing a couple k the turbo gave up so looked around for something a bit different, had loads of ideas;)but went for a vf23 bb turbo, then got a custom mani made and downpipe from ricky lee, when the car ws apart got rid of aload of stuff that you dont need,washer bottles, horn, power steering and clean and tidy up the engine bay, different intercooler piping etcwent from thisto this whole front end been repainted, inner wing's, and underneath, and interior removed and repaintedfew things on order,cusco 7 point roll cage, custom catch tank, custom battery box, overflow bottle, new seats, custom inlet mani,will put spec up later onSPEC:ENGINE5EFE BLOCK4EFTE HEAD, CAM'SCRUISE VALE SPRIGSZEP 1.2MM HGPAUTOR RODSWIESCO DISH PISTONS (10CC)LIGHTEN AND BALLANCE BOTTOM ENDAASCO LIGHTEN FLYWHEEL5E BOTTOM PULLEY (WITHOUT PS PULLEY)A/C COMPLETELY REMOVEDP/S REMOVEDALLY CIVIC RADCUSTOM RICKYLEE MANICUSTOM RICKY LEE DOWN PIPEHKS HI POWER SIDE EXITTIAL 38MM EXTERNAL WASTEGATESCREAMER PIPEBRAIDED WATER LINESBRAIDED OIL FEED AND RETURN LINEIHI VF 23 TURBOTRD ENGINE MOUNTSCUSTOM BAFFLED SUMPUNIVERSAL INTERCOOLERCUSTOM 2.25" BEFORE INTERCOOLER AND 3" AFTER INTERCOOLERFORGE DUMP VAVLECUSTOM INLET MANIBILLET 75MM THROTTLE BODYCOOLING PANELNGK HT LEADSHEAT RANGE 8 SPARK PLUGSACT FOUR PUK CLUTCHCUSTOM CATH TANKCUSTOM BATERY BOXCUSTOM OVERFLOW TANKFUEL SYSTEMRC 440CC INJECTOR'SCUSTOM ALLY FUEL TANK (25 LTR)FUEL SURGE TANKBOSCH 044 PUMPLOW PRESURE FUEL PUMPBRAIDED LINESSARD FUEL PRESSURE REGCHASSIS4WD15" 5 SPOKE 195/45 TOYO T1-4'SZEP RACING COILOVER'SCUSCO FRONT STRUT BRACECUSCO LOWER ARM BARCUSCO 7 POINT ROLL CAGE3G FRONT DISC'SMINTEX PADSEXTERIORFULL GT TURBO BODY SWAP, DOOR'S, BOOT, ARCHES ETCFRONT BUMPER CUT OUTAIREL REMOVED AND SMOOTHEDFUEL CAP REMOVED AND SMOOTHEDRESPRAYED MAZDA WINNING BLUECARBON BONNETQUAD LIGHT CONVERSIONWHOLE UNDERNEATH PAINTED BLACKTINTED WINDOWSGREEDY SUNSTRIPINTERIORCOMPLETE GT DASH SWAPGT COMPLETE WIRING LOOMSTRIPPED OUT BACK AND PAINTED BLACKCARPET REMOVEDPROSPORT GAUGESAPEXI AVCRTHATS IT FOR NOW, PROB FORGOT SOME Quote Link to post Share on other sites
Sparky Posted November 29, 2008 Share Posted November 29, 2008 One of my favourite builds on here, fucking insane!!That custom inlet is the bollocks, must of been expensiveDo you want me to delete your other thread mate? Quote Link to post Share on other sites
GAZ@A&G_TUNING Posted November 29, 2008 Author Share Posted November 29, 2008 cheers mate, it cost 550 euro ;) , if you could delete the other one that would be great Quote Link to post Share on other sites
Sparky Posted November 29, 2008 Share Posted November 29, 2008 Feck not that bad then!Who made it?Il do it now ;) Quote Link to post Share on other sites
5T4R7ET N/A Posted November 29, 2008 Share Posted November 29, 2008 that looks pucca. where did u get that made from.what additional gain are u expecting from this. ;) Quote Link to post Share on other sites
himmys gt turbo Posted November 29, 2008 Share Posted November 29, 2008 that is mental mate, lovin the colour ;) Quote Link to post Share on other sites
BenV Posted November 29, 2008 Share Posted November 29, 2008 that looks really good fella nice updates Quote Link to post Share on other sites
Dave@TM-Developments.com Posted November 29, 2008 Share Posted November 29, 2008 Who made it?I supply them Quote Link to post Share on other sites
RobSR Posted November 29, 2008 Share Posted November 29, 2008 ^ was going to say what headgasket were you running when it was detting? Quote Link to post Share on other sites
Liam_D Posted November 29, 2008 Share Posted November 29, 2008 One of the best Starlets there is out there mate!!! Quote Link to post Share on other sites
GAZ@A&G_TUNING Posted November 29, 2008 Author Share Posted November 29, 2008 thatnks for the comments dude's.i dont no who made the inlet mani as i am buying it from a fella in ireland, if dave b sells them he may no, rob i used a 1.6mm hg with wiesco low comp pistons, i was runing bout 7.8-9-1 f the top of my head Quote Link to post Share on other sites
GAZ@A&G_TUNING Posted November 29, 2008 Author Share Posted November 29, 2008 done a few things today, aze_b come round and made me up a custom side exit with hks hi power back box, screamer pipe was made and braided water lines-oil lines fittedalso removed inlet in prep for new onebottom pulley split as i dont use the power steering one, and a pic of aze welding which came out pretty cool Quote Link to post Share on other sites
Galliano Posted November 30, 2008 Share Posted November 30, 2008 looking good man, it has come a long way and you dont realise it untill theres a big compilation Quote Link to post Share on other sites
Starbus Posted November 30, 2008 Share Posted November 30, 2008 Looks cool, really like this car, Do you still need them bends? If you do text me your address tomorrow and i'l sort them out Keep forgetting, that'l remind me Quote Link to post Share on other sites
GAZ@A&G_TUNING Posted November 30, 2008 Author Share Posted November 30, 2008 cheers rick, na no longer need them now, had a few people on passion ford asking bout the mani, so expect some pm's over there Quote Link to post Share on other sites
Starbus Posted November 30, 2008 Share Posted November 30, 2008 cheers rick, na no longer need them now, had a few people on passion ford asking bout the mani, so expect some pm's over there Cool, i'm on with making a couple of cossy manifolds at the minute, PF is massive so hoping the word will spread a little I'm just sorting some little tags out for the manifolds so people know what they are. Quote Link to post Share on other sites
abbott Posted November 30, 2008 Share Posted November 30, 2008 Cool, i'm on with making a couple of cossy manifolds at the minute, PF is massive so hoping the word will spread a little I'm just sorting some little tags out for the manifolds so people know what they are.Ricky your gonna be busy in 2009 i tell you that, there is not that many great fabricators about which do work like yours. Good lick with it all get some window stickers off to me and gaz bit of extra advertisement for ya! Quote Link to post Share on other sites
GAZ@A&G_TUNING Posted November 30, 2008 Author Share Posted November 30, 2008 yeah mate passion ford is mad, by the time you have posted something and hit new post's, there are about 20 newer post ,send me a couple of them tags up mate, will put one on abbott's too Quote Link to post Share on other sites
Starbus Posted November 30, 2008 Share Posted November 30, 2008 yeah mate passion ford is mad, by the time you have posted something and hit new post's, there are about 20 newer post ,send me a couple of them tags up mate, will put one on abbott's tooYe, that'd be cool if you could, it'l be a week or so off yet, as i'm just finalising the design then they need to laser cut them. Quote Link to post Share on other sites
GAZ@A&G_TUNING Posted November 30, 2008 Author Share Posted November 30, 2008 sweet give us a bell when you have them ready, and will send over my address, Quote Link to post Share on other sites
SiCaln Posted December 1, 2008 Share Posted December 1, 2008 thats an awesome project man good on ya Quote Link to post Share on other sites
GAZ@A&G_TUNING Posted December 1, 2008 Author Share Posted December 1, 2008 this badbay turned up today, gave it a quick polish and trial fitting, need to ADJUST a few things but she fits nicely Quote Link to post Share on other sites
Sparky Posted December 1, 2008 Share Posted December 1, 2008 Immense!!Take it you need a different throttle cable and shorten the IC pipe? Quote Link to post Share on other sites
GAZ@A&G_TUNING Posted December 1, 2008 Author Share Posted December 1, 2008 cheers sparky, yeah just ordering up some new samco pipe up, and new to sort throttle cable and other feed's that come of inlet Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.