Jump to content

Dean_mc88

Member
 View Profile  See their activity

  • Content Count

    969

  • Joined

  • Last visited

 Content Type 

Everything posted by Dean_mc88

  1. Dean_mc88
    Good luck with the sale man nice little bike, lets see the other one
  2. Dean_mc88
    I'll have a go next week and be at the ready with some solvent to remove the glue ! Car does look a bit max power at the minute with the tints hate the wheels as well but that's another topic lol
  3. Dean_mc88
    Haha I think it's no tints, the thought of paying someone to remove them though is horrible, I can rebuild an engine I'm sure taking tints off shouldn't be a problem I'm sure?! Lol
  4. Dean_mc88
    Its looking that way isn't it lol I just wonder if its a major job ripping them off shouldn't be too bad should it ?
  5. Dean_mc88
    I got the glanza with tints on already. Ive never been a major fan of tints. I do prefer a clean look. the tint on the back window is coming off so the question is do I get it re done or rip the lot off ? majority vote will be the decision
  6. Dean_mc88
    absolutely spot on, very well packaged and quick delivery (parcel shelf) cheers mate
  7. Dean_mc88
    If it was me id buy supporting mods and have it mapped that's the only safe and sure fire way of getting the most out of it
  8. Dean_mc88
    yea just realised mate lol
  9. Dean_mc88
    .
  10. Dean_mc88
    pm'd about intake manifold
  11. Dean_mc88
    Gutted for you mate its a shame people just cant be honest ! glad its sorted now though
  12. Dean_mc88
    you have to be a paid member to post in for sale, You can get a paid membership at the store
  13. Dean_mc88
    I bought my glanza yesterday, I lift share and have a daily so wont be using it in this weather, however, when I looked at the car this morning it was frozen on the inside so I didn't even check to see if it started. Ill check tomorrow morning though for sure
  14. Dean_mc88
    Bought a carbon spoiler off him great lad great seller !!
  15. Dean_mc88

    Collect the glanza sunday!

  16. Dean_mc88
    Pm'd
  17. Dean_mc88
    yea spoke to the guy a quick email to them and they have STD 0.25 U/S AND 0.50 U/S
  18. Dean_mc88
    Yea but theirs 3 types so how do you know your getting the correct ones, also I've looked up the part numbers they have give and it doesn't seem to match, main bearing says 11701-10011 but when you look it up on toyodiy that part number should be 11701-10012 - 1,2 or 3
  19. Dean_mc88
    if your going to Toyota for parts surly you could tell them the number on the crank then say its undersize by 0.25? If got one of my mates in Toyota looking into it for me complete bottom end bearing kit my crank is within tolerance from original spec so its a lot easier for me. £76 pound just for big end bearings so im expecting a bit of a bill for the full set
  20. Dean_mc88
    cheers rich, not far from me so will have to organise some little runs !
  21. Dean_mc88
    I have exact sizes just wasn't going to list them all lol I'm a fully qualified engineer so all the equipment in work is spot on however I will be getting more than myself to measure just to clarify
  22. Dean_mc88
    Ah right fair enough ive just measured mine and there all the same, around 40.000 and the bigger parts are around 47.000 That's a crank I have bought that is not the damaged one
  23. Dean_mc88
    just because im going through the same issue with mine what is standard size of the crank?
  24. Dean_mc88
    sounds like a mad little project - welcome along
  25. Dean_mc88
    cheers Calum need to make it my own though lol Hi Phil ! yea man long time ! with oil prices being so low not had chance to travel as much but still get about was in Nigeria earlier in the year
×
×
  • Create New...