Jump to content

Recommended Posts

Time for a little update before Japfest 2.



Had a few set backs which mean at this time im a little unsure wether i'll be coming in my car to japfest 2 :cray:



Firstly had a machanic i no come to mine last week to try and fit the WMS (i dont touch my brakes just in case i do it wrong!) and they didnt fit. So i'v been in contact with keri, i have sent mine back to get them sorted and he is hoping to get them back to me by Thursday fingers crossed!



Then had to go in for my MOT saturday morning, failed on the back brakes Great! so got hold of a new Caliper which should be with my tomorrow and then i can get them on and retested Friday if it all goes to plan!



But despite this i have ploughed on hoping i will still be there. Gave the engine bay a clean up, gutted the inside and fitted my new bonnet.



Bought lews bonnet back in January but finally got round to sorting it out, re did the gold tape and lew cleaned it all up for me and helped fit :)



20130630_154454_zps44bb42ea.jpg



20130630_155704_zpsa10bcd29.jpg



20130630_155620_zps6d8a8ff7.jpg



iuf_zps3b3ca4b0.jpg



Gave the inside a good clean and scrubbed the back out were the seats and been and in the wheel is a but rusty but i'll be getting it sorted soon for now I've just cleaned it up.



werty_zps4e894506.jpg


Edited by *Zoe*
Link to post
Share on other sites
  • Replies 230
  • Created
  • Last Reply

Top Posters In This Topic

Why's lew sold the bonnet? What's he upgraded too? Looks good Zoe.

he bought a new one because his had a few stone chips ...doesnt bother me so i bought it off him lol worked out good this bonnets pretty much new no peel and the chips you can hardly see .

Well happy :p

Link to post
Share on other sites

Time for a little update before Japfest 2. Had a few set backs which mean at this time im a little unsure wether i'll be coming in my car to japfest 2 :cray: Firstly had a machanic i no come to mine last week to try and fit the WMS (i dont touch my brakes just in case i do it wrong!) and they didnt fit. So i'v been in contact with keri, i have sent mine back to get them sorted and he is hoping to get them back to me by Thursday fingers crossed! Then had to go in for my MOT saturday morning, failed on the back brakes Great! so got hold of a new Caliper which should be with my tomorrow and then i can get them on and retested Friday if it all goes to plan! But despite this i have ploughed on hoping i will still be there. Gave the engine bay a clean up, gutted the inside and fitted my new bonnet. Bought lews bonnet back in January but finally got round to sorting it out, re did the gold tape and lew cleaned it all up for me and helped fit :)20130630_154454_zps44bb42ea.jpg20130630_155704_zpsa10bcd29.jpg20130630_155620_zps6d8a8ff7.jpgiuf_zps3b3ca4b0.jpg Gave the inside a good clean and scrubbed the back out were the seats and been and in the wheel is a but rusty but i'll be getting it sorted soon for now I've just cleaned it up. werty_zps4e894506.jpg

What was the problem with the breaks Zoe? I fitted mine and all was good until I tightened up the wheels which then locked the brakes

Link to post
Share on other sites

I made it to Japfest 2 Woo Hoo!



It wasnt easy tho alot of stressing and running around but Brakes are fitted and shes Mot'd



Got a refurbed caliper of ebay for the back as mine was not working at all !! I got this rushed to me last week so i could get it fitted for my MOT retest. It was pretty clean but the guy painted it yellow....this wont be this colour for long!



http://s972.photobucket.com/user/buggs1989/media/20130705_121029_zpsd27545b4.jpg.html'>20130705_121029_zpsd27545b4.jpg



Then it was time to fit the front brakes. Keri had done a great job turning these around for me in a week i sent them to him on Monday and i had them back on friday, Grooved and Re-drilled for my hub size. So happy with them



http://s972.photobucket.com/user/buggs1989/media/20130705_112857_zps9a023d0c.jpg.html'>20130705_112857_zps9a023d0c.jpg



http://s972.photobucket.com/user/buggs1989/media/20130705_112912_zpsb170432d.jpg.html'>20130705_112912_zpsb170432d.jpg



http://s972.photobucket.com/user/buggs1989/media/XCVB_zps5b86e47a.jpg.html'>XCVB_zps5b86e47a.jpg



All fitted with braided lines and EBC yellow stuff pads.



This is wear it gets interesting, lew had lent me his 6mm spacers which when it was on the ramp the one side we tested they spun fine. So fitted the other side and dropped it down. When i drove of i heard a clunk....pulled over the side we hadn't tested was bashing my squeeky clean new caliper :cray: so to get home lew came out to me and we jacked her up and added a 3 mm spacer on each side to get me home. Oh yeah 2 of my wheel nuts (rays!) thread disintegrated two just for extra fun so only had 3 nuts on each front wheel!



http://s972.photobucket.com/user/buggs1989/media/YHG_zps47fc9026.jpg.html'>YHG_zps47fc9026.jpg



Saturday went out and got myself some 10mm spacers to sort this mess out but it couldnt just be take easy could it! then my bolts werent long enough and no one stocks the lenght i needed.....just about to through in the towel and go in Lew's but he came to the rescue. With giving me a christmas present early, bought me a set of 3 spoke Advans so he swapped the tires over and because the spokes are bowed they fitted straight on with no spacers. So Happy and made the show.



Then i fitted my new Cusco front Strut brace :



http://s972.photobucket.com/user/buggs1989/media/20130706_163018_zps061daeee.jpg.html'>20130706_163018_zps061daeee.jpg



http://s972.photobucket.com/user/buggs1989/media/20130706_163006_zps33467111.jpg.html'>20130706_163006_zps33467111.jpg

Link to post
Share on other sites

What was the problem with the breaks Zoe? I fitted mine and all was good until I tightened up the wheels which then locked the brakes

Keri sent the wrong hub size, 54 instead of 55. he sorted it out really quick tho and there on now :)

Link to post
Share on other sites

Keri sent the wrong hub size, 54 instead of 55. he sorted it out really quick tho and there on now :)

Ah right glad to here they sorted it out fine, my brackets had been machined wrong which needed shimmes to align them up properly

Link to post
Share on other sites

Getting some updates on at the minute! Bought another piece of the puzzel on Tuesday night from Yaris Turbo, top lad :)



Some tasty Meister R Coilovers :D



http://s972.photobucket.com/user/buggs1989/media/20130710_222057_zps8b17ec84.jpg.html'>20130710_222057_zps8b17ec84.jpg



http://s972.photobucket.com/user/buggs1989/media/20130710_222155_zps28cfaa48.jpg.html'>20130710_222155_zps28cfaa48.jpg



http://s972.photobucket.com/user/buggs1989/media/20130710_222043_zps3fdd7b71.jpg.html'>20130710_222043_zps3fdd7b71.jpg



Trying to get these on at the weekend, should sort out the back end being on stilts since i stripped it out.


Link to post
Share on other sites

Looks great Zoe well done! :)

Thanks Browner :thumbsup:

Got another package!

http://s972.photobucket.com/user/buggs1989/media/20130721_1828481_zps946ea8fe.jpg.html'>20130721_1828481_zps946ea8fe.jpg

Picked this up on here last week, needs a good clean and will be spraying it black but hopefully get this on in the next few weeks :)

getting the coilovers in this week to its all coming together should be quite different for JAE !!

Link to post
Share on other sites

cant be bigger than mine lol....actually thats not true but... mine are pretty large as well ....



cant be bigger than mine lol....actually thats not true but... mine are pretty large as well ....

^^^^ hahahah just realized how much of a thats what he said moment that was lol

Edited by rasslenny
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...