Spoon_tuned Posted October 28, 2012 Share Posted October 28, 2012 hi guys after recently selling my eg SiR i was on the lookout for a new car i wanted to go down the ep3 route as they looked smart engines are bullet proof and there kinda new and i wouldnt have too do anything to it other than wheels exhaust and lower it.but my dream civic i always wanted from day one was a Ef9 as they were hard too come by years ago when i first wanted one so i bought an eg esi instead and from then i just stayed with eg's vti's SiR's etc etc.but after i sold my SiR B20 recently i found an Ef9 SiR on the internet and i new instantly i wanted it as long as it had no rust!!! but the problem was it was in scotland DOH!! so after ringing the lad up he assured me it was mint and sent me dozens of close up photos of the arches etc etc too show there was no rust. so i sent him a deposit and said i'll be up in a weeks time and he was kool with that i just didnt want it to be a waisted journey to turn up and and see big dents scratches rust but the lad was very honest in fact he stated everything that was wrong with it not a very good salesmen lol. but the the things were minor like a little scratch on the wing lacquer peel on the roof,and abit of fading on the front bumper.so after abit of persuading my cousin decided he would take me so after 7hrs we finally arrived in angus!! saw the car instantly wanted it checked it all over went for a test drive had a long chat handed over the cash and started the long journey home!my cousin wanted too take some shots on the sea front so we did.Spec:B16A SiR EngineRace Clutch Unsure Of Make4 -2-1 Manifold [Rs*]Straight Thru Decat SystemNgk LeadsApexi Induction KitLong Arm IntakeFront Strut BraceRear Strut BraceSprint Heart RimsParada Spec 2 Tyres all RoundMeister R CoiloversShort ShifterPowerflex Shifter BushingsEnergy Rear Suspension BushesNardi Signature Series WheelFront Tilt Bracketjust serviced it fresh oil,fuel filter,plugs,oil filter,oil flushed,water flushed also just got to underseal again soon also got too silicone rear lights as they have water in and silicone above the lights as it has water getting into the boot which is annoying heres some pictures of my progress!!!!when i first got it in scotland!Clean::1st problem i came across which i knew would be a problem is trying too fit my twinpot calipers i need spacers but big ones so think i got too sell them now as im not changing my wheelsits only because of the dish on the wheels its a shame as i really wanted too use the calipers i could use a spacers and shave them a little but its a ball achenext problem was my windscreen wipers stopped working so today i stripped the plastic off and tried too source the problem i found out that the arm had come off as the plastic ball clip on the back are crap so i managed too get them back on but its just how long it will last unless i can find some new clips plus sometimes they dont come all the way down and sometimes they do which is a mystery but i did notice the splines do look abit worn so maybe i need new ones!!Things To Do:underseal car againre-paint the wheelssort out leak in bootfix rear lightspaint front bumper,spoiler & roofclean up engine bayget new solenoid gasket as its leakingget new brake discs & padsfit 1 inch m/sNext..Well a pretty shit day tbf first of all i got up at half 6 this morning ready to travel too bristol to fetch some winter wheels i went to the garage too fill up and put water in my jets.i put £1 in the machine fill up with water but the screen wash wasnt coming out then i released theres a tap on the side u press stupid because i didnt have a bottle too put it in what a stupid design!!!!!then going down the motorway my windscreen wiper goes too far across comes off the windscreen and hangs on near my drivers side mirror so i pulled over to push it back down and realised the arm had come off yet again!!!!!so i was pissed off before id even got there as its scratched all my pillar and took some paint off!!!!so finally got there to meet alex [i hate speed bumps] nice lad and the wheels were ok needed a refurb and paint but i new this all the tyres were good but the profile on the back tyres were 205 55 15 and the front 2 were 195 55 15 i thought this may be a problem which i later realised when i got home!!!!then when i got home my manifold started blowing even more than before and now sounds like a tractor!!! so i got out too check it and when i revved it i could see the bolts from the down pipe too manifold were moving and i found out a nut was missing and the other 2 bolts were not even hand tight they were nearly hanging off!!!so that put me in a mood then fitted the wheels and yep i was right the car wouldnt move as the tyres were rubbing the arches so all in all a great day!!!ok got my new parts today all the gaskets for my exhaust as it's blowing and my vtec solenoid gasket so hopeful if this rain holds off i can get all my stuff sorted!!!firstly this arrived this morning from my g/f who had bought me this for my birthday so i tried too sort my manifold today but i couldn't do it all bolts were fused and really awkward when its raining and theres 100mph winds.so a quick phone call too my mate and late afternoon i took it too his uncles garage. on inspecting it he found that the gaskets i'd been given were wrong which i kinda thought they were so he had too use loads of sealant until my gasket arrives still it sealed it and runs so much smoother than before..i'm going to order some heat wrap and the proper gasket and have him do it again when he gets time then i had a phone call from my mate to say my wilwoods were ready to collect as ive been waiting for these for ages as he was trying to get the correct spacers for his g40 polo and didn't no which pair too keep because he had 2 setsnot bad for £60 a set:) just need to get some brackets and brake pads now Quote Link to post Share on other sites
Spoon_tuned Posted October 28, 2012 Author Share Posted October 28, 2012 Update From Saturday MorningRight so i got up really early to get this stupid leak done that was coming from my solenoid gasket. The week before i changed the gasket for a new one thought all was kosher until later on i checked and there was more oil dripping than before wtf?so i decided too strip most of my EF down from the dizzy too all water pipes and battery just so i could get too the bolts properly my EF bay is so tightly packed compared too my old Eg.Got it all off and found the gasket on the solenoid was really baggy and didn't seem to fit properly and was split good job i kept my old one so i put the old one back on and used a bit of silicone gasket and i think i've sorted it now fingers crossed.All Back Together Just Needs A Good Steam Clean!!right i went too see jody aka RECEG6 last night too lend some wilwood caliper brackets and today i had a look at the brackets to see if they were the right ones and they fit perfect but!! i need bigger discs DOH! but the problem is they won't fit under my wheels which sucks as i dont want too change my wheels so i guess they'll have too be soldAlso forgot too mention i also bought a 1 inch master cylinder like months ago lolHad a recent meet in coventry so i spent a few hours cleaning my car last week heres the picturesThen These Arrived In The post This Morning Then These ArrivedNot much of an update as you will all know the weather has been awful but will have alot more progress once the weather starts to get alot warmer Quote Link to post Share on other sites
Spoon_tuned Posted October 28, 2012 Author Share Posted October 28, 2012 Sorry for the lack of updates not much changed in a while So for the updatesMe & my friend Rob decided to adjust my tappets last week because my engine seemed a lot louder than my friends Eg so i went and got me a feeler gauge and got cracking !!The exhaust side wasn't so bad but the intake side was a lot looserSounds a lot better now but my alternator belt is worn and sounds horrible Mot monday so all will be sorted!!! Well car failed miserably which i already knew it would as the previous owner had a dodgy MOT on itbut it's mainly only silly little things tho which isn't badwent to a scrapyard today afterwards and found me a nice ED7 which i bought a few bits offYES!!! windscreen wiper Rotas and arms so now i can get rid of that stupid single wiper conversion and i also got the catch for my loose glove box and nice Rubber dash board cover which i didn't notice until last minute!!!!also it has some mud flaps which i might go back and get Right few parts ordered today first came my energy suspension bushes, then i picked up some brake fluid and a cv gator for my driveshaft for my m.o.t gunna get up early tomorrow cause jaydog81 is on his way down and we got a lot of jobs to do on the EF for my m.o.t plus gunna try and fit my 1 inch master cylinder and Cusco strut brace car passed Mot yesterday after alot of messing around and lack of commitment felt nice to drive my car again after over a month of not driving itfailed on trailing arm bushes and cv gator so got on with removing the trailing arm and BOOOOOOM!!!! my mate snapped the head off the bolt because it was seized so after hours over trying to drill it out we managed to remove the trailing arm with messing up the lca bushes so we got on with fitted the bushes then got all them fitted forgot the photos tho!! so put everything else back together and ordered some rear trailing arms received them and fitted my braided lines all round to so started adjust my handbrake cables so started stripping out the centre consolebut now ive ran into a problem with my rear calliper the spring for the handbrake cable keeps seizing up which makes the brakes stick on sometimes and is making that humming noise that gets faster the faster you go so i'm still not driving my car after all the work ive done rushing yesterday to get to the mot centre lol so just took a few photos best one|!weather was good so got on with doing the rear calipers tried to un seize the drivers side rear caliper but the handbrake springs has had it so on the look out for another one but at least for now its not making a stupid noiseAll Cleaned up Afterwards Quote Link to post Share on other sites
Spoon_tuned Posted October 28, 2012 Author Share Posted October 28, 2012 Just a little picture from the flood street meet now [JDMC]Not much until after the weekend as i'm going up to jaydog81's house for the weekend to work on my car These arrived Things To Do This Weekend:Master Cylinder Change ['1 Inch'] Weld Manifold Weld BackboxFit All Belts Paint CalipersFull Service:And A Really Good Cleani've just noticed half my thread is missing so i'll just upload a few pictures i took with my DSLR camera i recently purchasedRight so i got a lot sorted the weekend which i'm happy with we sorted the master cylinder welded all my exhaust & manifold fitted my new powerflex bushes gave it a service fixed my leak coming from under my wipers & heat wrapped My manifoldwas a good weekend and we managed to go for a drive and take some pictures still a few things to sort like my rear caliper sticking but jamie gave me a set of rear refurbed calipers that i'll fit soon as i get a chance and we did'nt get round to fitting my new belts but will sort that in the next week or somy master cylinder was leaking onto the servo tiny bits every so often which it started to erode my servo thats why i had no pressure in my brakesNew Servo & Cylinder FittedHamp Shortie FilterNew Bushes & Welded A Plate On The Exhaust Stop It CatchingJamie Welding My ManifoldAnd Just A Few Photos From The WeekendGot some more bits yesterday that i need for my exhaust and my calipersAnd also got given these from jaydog81 Rear calipers with new seals : Still having problems with my brakes i'm thinking they may need Re-Bleeding again & some new brake padsbecause these are crap unless there hot after hard braking they work wicked but still i have a spongy pedal if after bleeding and new pads the brakes are still Rubbish then i'm gunna have to rip out the ABS unit because i think it's faulty BUMMER!!!!I recently went round to see my cousins new EG and he told me he was getting some nice rims well when i went back a few days later BOOOOMBBS Splits Rims which i really needed to try out on my car lol i had to put the 2 back wheels on as the fronts splits was'nt no where near as wide he's gotta get some new dishes for the front which are very expensive so i only tried on the one side but hey what the hellHere's a few picsHad time the weekend to try get brakes sorted so i changed the sliders from my calipers to the new ones Jaydog81 gave me with all the new seals so i put the seals in greased everything up and put them all back on. Then i bled the brakes but still the rear drivers side disc doesn't look like it's been working properly now this is three sets of calipers i've had now and my brakes are still really spongey..so i think ABS needs removing as these brakes are really shocking New Sealsust a few pictures from today a bit of caliper painting!Some Shots From Jae At The WeekendAnd A Couple I Stole From GIZMOSomething that has been doing my head in for ages 70mph wheel shake spigot rings there was'nt any on my sprint hart wheels so purchased some off ebay but guess what wrong size they didnt quite fit so had to shave them slighty with a stanley knife and use of my heat gun yet to test my car yet but i'm gunna try it later see if i still get the really bad shake fingers crossedJust a quick edited on my cousins bbs rimageNew Parts ************As some of you may know my best mate jaydog81 is in the process of breaking his B18 eg5 and i wanted a few parts from him and what he has charged me i could not say no and the parts are quality as of all the stuff jamie buys it's never tat he always spends over the odds for things just to keep things clean & tidy ANYWAY enough of that muppet Quote Link to post Share on other sites
Spoon_tuned Posted October 28, 2012 Author Share Posted October 28, 2012 Parts Are On!!!!!Done a little bit today fitted everything apart from solenoid cover as it was to small took a while to get the horn working on the steering wheel as i had to add another wire to it but it's all working now it's a tad bit smaller than my previous wheel but feels alot better.Door speakers are also in now and are pumpin! also fitted the spoon socks but as i have a cable clutch there's no clutch bottle to put the sock round so i put it on my water washer bottle leads are all connected now just wish i had time to polish today oh well i'm off work for 10 days now so i can get alittle more done that needs doing Went out last night with my mate as weve been wanting to get a few pictures of the cars for a while now the weather was ok a little bit windy but managed to get some ok shots anytime we want to get photos we can never think of anywhere with lights so we ended up in a car park Enjoy!And me being a dick All Copied From Civiclife.net Enjoy Quote Link to post Share on other sites
Jack-CTR Posted October 28, 2012 Share Posted October 28, 2012 looks clean mate! im sure I've seen the car at flood street Quote Link to post Share on other sites
Stefan_s Posted October 28, 2012 Share Posted October 28, 2012 Looks awesome mate always loved these and it was in Angus, thats where imfrom lol Quote Link to post Share on other sites
morgey Posted October 28, 2012 Share Posted October 28, 2012 very impressive mate, but one thing thats more impressive....and thats how tall you are..... Quote Link to post Share on other sites
Spoon_tuned Posted October 28, 2012 Author Share Posted October 28, 2012 very impressive mate, but one thing thats more impressive....and thats how tall you are..... hahaha nah man i'm usin the tripod holding it up really high on remote.looks clean mate! im sure I've seen the car at flood streetthanks mate yeah been flood street a few timesLooks awesome mate always loved these and it was in Angus, thats where imfrom lolyeh bought it a while back from angus done alot to it since then i've tidied it up Quote Link to post Share on other sites
Malcolm GT Posted October 28, 2012 Share Posted October 28, 2012 Clean motor, like these old civics. Makes a change from ep3's or ek series Quote Link to post Share on other sites
Spoon_tuned Posted October 28, 2012 Author Share Posted October 28, 2012 Clean motor, like these old civics.Makes a change from ep3's or ek seriesthanks yeh these are a different league to an Eg Ek Ep3 Dc2 the feel of them is awesome round corners ,there solid and the power delivery is wicked for such an old car. Quote Link to post Share on other sites
Hawwy Posted October 28, 2012 Share Posted October 28, 2012 am sure this is for sale on ph Quote Link to post Share on other sites
Spoon_tuned Posted October 28, 2012 Author Share Posted October 28, 2012 and you'd be right Quote Link to post Share on other sites
Hawwy Posted October 28, 2012 Share Posted October 28, 2012 you selling it and u just made a thread on it? Quote Link to post Share on other sites
MARC MOSS Posted October 29, 2012 Share Posted October 29, 2012 He wants boost I reckon Quote Link to post Share on other sites
smobey_sutton2 Posted October 29, 2012 Share Posted October 29, 2012 you selling it and u just made a thread on it?He's copied this thread over from civiclife.net, just giving us a nice read Quote Link to post Share on other sites
mattyD Posted October 29, 2012 Share Posted October 29, 2012 best shaped civic by a mile dude, fucking love them as marc said, dying for a small amount of boost though ;) Quote Link to post Share on other sites
Spoon_tuned Posted October 29, 2012 Author Share Posted October 29, 2012 (edited) yeh i put my thread up for people to read not to try sell it people. i'll still update til it sells just thought people might like my build up and the effort i've put in.i am after a glanza td04 now and yes i want to go boost i've had 2 starlets before ep82 auto & a ep82 manual but the piston rings went a week after buying it i had that much trouble with it i went back to civics because i know them cars inside out.just fancy a change i'll update this as and when i can Edited October 29, 2012 by Spoon_tuned Quote Link to post Share on other sites
Spoon_tuned Posted October 29, 2012 Author Share Posted October 29, 2012 best shaped civic by a mile dude, fucking love them as marc said, dying for a small amount of boost though ;)thanks mate i'd love to boost this but dont have the money dude plus i fancy a change after having civics for 7 years Quote Link to post Share on other sites
LukeSR Posted October 29, 2012 Share Posted October 29, 2012 Alrite Aidy Quote Link to post Share on other sites
PaulStarletSR Posted October 29, 2012 Share Posted October 29, 2012 Lookin sweet bud Quote Link to post Share on other sites
Spoon_tuned Posted October 29, 2012 Author Share Posted October 29, 2012 Alrite Aidy alright luke hows it goinLookin sweet budthanks mate Quote Link to post Share on other sites
Michael! Posted October 29, 2012 Share Posted October 29, 2012 thanks mate i'd love to boost this but dont have the money dude plus i fancy a change after having civics for 7 yearsHow much are you looking to sell this for dude??Mike. Quote Link to post Share on other sites
Spoon_tuned Posted October 29, 2012 Author Share Posted October 29, 2012 How much are you looking to sell this for dude??Mike.i put it up for £3750 o.n.o it's well worth the money though and it's the only one in the country for sale very very rare car . ask luke SR he knows my car Quote Link to post Share on other sites
Starbuck Posted October 29, 2012 Share Posted October 29, 2012 Looks nice. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.