-
Content Count
8788 -
Joined
-
Last visited
Content Type
Profiles
Forums
Wiki
Media Demo
Store
Calendar
Everything posted by morgey
-
A few of my mates are heavy into hardhouse hardstyle and all that sort of stuff. We'll be blasting it out on the decks at JAE and raving it up in our tent
-
Not the 5efe(5efhe) one from a while back??
-
Cables for disc brakes?
-
After 120 the gtr would walk, on track the gtr would walk (with the right driver) 0-120 the gtr would walk 50-80/100 the starlet would probably have it. Right terms for the starlet and it shows.
-
98 rear bench, Calipers, braided lines, Gt wishbones more added
morgey replied to morgey's topic in Starlet Parts For Sale
They are fronts im afraid. I have got 2 spare sets of rears but they need refurbing. -
Buy meister's lol Could always remove one of the locking rings?
-
You'll be very hard pushed to have just a starlet stand. Id like to see a marquee go in a starlet along with all your drink, food, camping gear and other shit. Just make him carry loads of shit! Support vehicles ftw!
-
£63 fuuuuuuuuuuuck!!! You lucky sod!! Haha
-
Oossshhtt that bride covered rear is nice! You going to darken up the sides? Haha glad to see you got the F/W too
-
An they did, they got what they deserved as well Yeah meet soon, make it a general toyota one to get more people down?
-
It depends on how far forward your engine sits. I think yours is slightly further back than mine so you should be ok. But mine the lower pipe is rubbing on where the front engine mount (or 4efte downpipe brace) bolt to. I've got a sleeve on where my pipes rubbing though. Mount kits fine. Tegiwa rad is also what im running. If anything its slightly too good a my temps are a tad cold, but im going to replace my thermostat to hopefully cure that
-
98 rear bench, Calipers, braided lines, Gt wishbones more added
morgey replied to morgey's topic in Starlet Parts For Sale
More added. Offers considered -
Have you got an anti lift kit? They make the wishbones sit lower and slightly closer to the arb. Maybe parts have worn in and sagged slightly. Only other thing is Exhaust in the tunnel? Worn rubber or maybe ones even split. Engine will move quite a bit when setting off so expect that to move a fair amount. Try putting a cable tie tight around the rubbers to reduce movement.
-
Im using motul rpf 600. Had good reviews and was recommended it also. Think i only used 0.5L's but i bought 1L incase
-
Have you got a thicker farb? Mine sat right close at the sides of the exhaust tunnel, had to bend some bits out the way, and i say bend i mean smack the shit out of with a hammer through a block of wood, because it knocked.
-
Glad it arrived swiftly! as always Happy to help
-
PaulStarletSR's TD04 Turbo'd beast. PROBLEM MAYB SOLVED
morgey replied to PaulStarletSR's topic in EP91 Progress Blogs
Chalk board paint and create an authority title for it lol Ill be bringing my chalkboard bonnet along to get signed and abused- 685 replies
-
- livesports
- zep
-
(and 8 more)
Tagged with:
-
PaulStarletSR's TD04 Turbo'd beast. PROBLEM MAYB SOLVED
morgey replied to PaulStarletSR's topic in EP91 Progress Blogs
Good good! Genuinely cant wait to see this thing driving again Im planning some bits to mine but not sure if they'll be in place for JAE. Will be ordering some stuff when i get my new bank card- 685 replies
-
- livesports
- zep
-
(and 8 more)
Tagged with:
-
PaulStarletSR's TD04 Turbo'd beast. PROBLEM MAYB SOLVED
morgey replied to PaulStarletSR's topic in EP91 Progress Blogs
Getting there No time to slack now! Less fb updates and more time working on it ;) haha- 685 replies
-
- livesports
- zep
-
(and 8 more)
Tagged with:
-
Well there might be, its hard to see on my phone
-
Aint seeing no fmic?
-
Needs about 400hp though not 70hp or what ever the 2e-e is pushing out lol