StarletMad

Although they can all be welded cant they?

am i correct in saying one of the Rev's has got the better diff?

In all fairness though im only 21 Suprisingly Mr2 insurance is under a grand so think i might go that route. and they go sideways

Im toying between Subaru Impreza Sport or Mr2 Turbo ???

So i did What a Wanker lol

Im gonna have to throw this one in Ive watched it 5 or 6 times

I was messed around by him for a little while but all got sorted in the end. Wasnt a nasty guy or anything. Seems a good lad i guess

Tapatalk ??

There no way they could have got from northants to the M25 without filling up.

Apparently from CCTV the was a half cast guy driving and a white passenger

As above ^^^

I expected a more in depth comment from Pervy GIf Luke Above ^^^ lool Just showed to the lady in our office... She got all Giggly haha

Definatly Nick the misses hair dryer

LoL Fair Play Duder

Alsi had this put down to Over Revving Earlier :/ Cant really see it tbh ive never bounced it off the limiter ever lol :/

Out the top tie a rope on furthest left exhaust stud and furthest right inlet stud ( Put a nut on each ) You will need a hand get someone to pull engine away from gearbox and just take the crane up slowly and move it back as you go Easy mate!

Took my 3 and a half pistons out today.... After abit of De-Greasing and on closer inspection the 1,2 and 3 Pistons have hairline cracks in exactly the same place as the number 4 one has broken up if that makes sense. Id put this down to When the gudgeon pins were put in wouldnt you??

Dont think hardly anyone get payed for Travel time bud. I used to start work at 7.30am.... Was up and leaving at 5.20am every day Not leaving site until 5pm and then not getting home until 7pm ish Only got payed for my time on site

Good Effort

Cant help but stare at the road... Makes me feel Dizzy!

Soorry bud yeah Variable Valve Timing No Point Grieving just un insure the little beast and save some pennies lol Make it A Special car this time round do it all properly and proffesionally and save myself the hassle time and money in the future! It makes sense. If you look at the cams one of them has a thinner "Sprocket" next to it The Thinner plate should push up against the thicker one and run in sync. Mine Wasnt

Not Alot to say really apart from whoever built it did it with there eyes shut! VVT was NOT set correctly. Theres no reason for piston rings to go unless its been put together poorly I think people forget that when putting Gudgeon pins it its not a case of just pushing these ones in the heat pressed in!! My Mechanic reckons they could have weakened the piston when putting the pins in. Sold to me as only done 4,000 miles Since Rebuild Wiseco Pistons and SCAT Rods etc etc..... Fairplay the Rods are Gleaming and look the real deal but Fuck Me the pistons are Bolloxed lol Pistons appear to be an oval Shape and the movement is unbelievable... if pushed to one side i guess youve got about 2-3mm gap Also You should see the state of the Main Bottom Pulley where its just been beaten off with a hammer befor only half of the inner edge remains! Just wish people would be honest when selling stuff. ANNOYING! Bolts missing here there and everywhere one off the top engine mount one off the alternator and 3 off the plate that goes around the gearbox..... SHODDDDY! Anyyywhooooo....... Here it stands now: Gonna give it a massive clean up and get the whole lot sent off see if i can get it Sorted at a Specialist See what i can do tbh thats all i can do for now. May just have to buy a second hand engine and make one good out of the bits.

No not yet buddy going to get the hoist and stand tomorrow... Oh well any excuse to clean everything up and change my clutch and do an oil change

What i found this afternoon Looks Like Piston Number 2 ... Also Piston 4 Has a few dinks in the bottom from what we can see. Going to take the engine out tomorrow evening and take the head off and ivestigate more. Anyone Selling some Forged Pistons LOL??

Ive Run 1 bar since nov mate