5e colin Posted July 8, 2016 Share Posted July 8, 2016 (edited) there you go if it fancies your tikkle Edited July 8, 2016 by 5e colin Link to post Share on other sites
SpikeyJp_68 Posted July 8, 2016 Share Posted July 8, 2016 Seen one of these on TGTT..Selling because there was an awful constant whining noise coming from the top end and was too costly for him to maintain... Link to post Share on other sites
Ryan-4444 Posted July 8, 2016 Author Share Posted July 8, 2016 Hahahah sounds like my type! What's your best price 😂 Link to post Share on other sites
Ryan-4444 Posted July 8, 2016 Author Share Posted July 8, 2016 How long has this one been leaking from top end and does it have much rear end damage from previous owner? Link to post Share on other sites
5e colin Posted July 8, 2016 Share Posted July 8, 2016 (edited) How long has this one been leaking from top end and does it have much rear end damage from previous owner? think so she must be fairly loose think this belongs in the naughty section ha ha Edited July 8, 2016 by 5e colin Link to post Share on other sites
Ryan-4444 Posted July 8, 2016 Author Share Posted July 8, 2016 That's the exact same face I have when on boost 😂😂😂 Link to post Share on other sites
daniel_g Posted July 8, 2016 Share Posted July 8, 2016 Rear main seal is shot, bottom end is a bit noisey, input shaft seal is very worn and leaks like a bastard. Has some amount of induction noise and screams like cunt at full chat. Link to post Share on other sites
lukEp Posted July 8, 2016 Share Posted July 8, 2016 Been told flange sealant is good for input shafts seals. Link to post Share on other sites
Siwfc Posted July 8, 2016 Share Posted July 8, 2016 That may need a rebore by the looks! Link to post Share on other sites
SpikeyJp_68 Posted July 8, 2016 Share Posted July 8, 2016 That may need a rebore by the looks!Never mind a rebore, it's well over the 75mm serviceable limit !! Link to post Share on other sites
Gainzy Posted July 8, 2016 Share Posted July 8, 2016 That burning rubber face... Link to post Share on other sites
5e colin Posted July 8, 2016 Share Posted July 8, 2016 ha ha right laugh just spat out half mi bottle reading this Link to post Share on other sites
Rob H@RCH Engineering Posted July 8, 2016 Share Posted July 8, 2016 I'm sure you could get some darton sleeves for it, be tight as fook then!! And take more boost! 🍆💦 Link to post Share on other sites
Martingdavies1985 Posted July 9, 2016 Share Posted July 9, 2016 Any piston slap? Bore wash? Link to post Share on other sites
5e colin Posted July 9, 2016 Share Posted July 9, 2016 (edited) poor fella some piston slap indeed / might be tighter up her ass Edited July 9, 2016 by 5e colin Link to post Share on other sites
Calum122 Posted July 9, 2016 Share Posted July 9, 2016 Well lads, I took it to a specialist and they agreed that it's well past its serviceable limit, it's only good as a paper weight now... Link to post Share on other sites
SpikeyJp_68 Posted July 9, 2016 Share Posted July 9, 2016 I'm extremely surprised this hasn't been deleted or moved yet... The wait continues Link to post Share on other sites
5e colin Posted July 9, 2016 Share Posted July 9, 2016 I'm extremely surprised this hasn't been deleted or moved yet... The wait continues no it wont it will get moved into the correct section as we have 1 for it ha ha ha Link to post Share on other sites
Recommended Posts