Glanza-Ben Posted November 28, 2014 Author Share Posted November 28, 2014 Little bit done today, removed old air con pipes from bulk head and fed wiring for, emanage map sensor, boost controller loom, oil temp and pressure wiring and water temp wiring also removed the emanage fron the glanza ready to wire into the gt Quote Link to post Share on other sites
Glanza-Ben Posted November 29, 2014 Author Share Posted November 29, 2014 Since the ends of the strut were painted and nice I gave the bar a quick polish Quote Link to post Share on other sites
Glanza-Ben Posted November 30, 2014 Author Share Posted November 30, 2014 Got up abit early today do do a couple bits, intercooler is fitted and sat behind bumper with no cutting at all, strut brace refitted, polished inlet and done a couple other bits, just need to fix radiator in place and clean a few more bits in the bay Quote Link to post Share on other sites
Glanza-Ben Posted November 30, 2014 Author Share Posted November 30, 2014 just ordered a new boost gauge Quote Link to post Share on other sites
akyakapotter Posted November 30, 2014 Share Posted November 30, 2014 Expensive gauge you got there mate. Quote Link to post Share on other sites
Glanza-Ben Posted November 30, 2014 Author Share Posted November 30, 2014 Expensive gauge you got there mate.You showed me it was to nice to refuse ;) Quote Link to post Share on other sites
fiddlersport Posted November 30, 2014 Share Posted November 30, 2014 nice gauge, saves the headache of having too many gauges in the dash, if it a bit cheaper would consider it ! good job on the build Quote Link to post Share on other sites
Glanza-Ben Posted November 30, 2014 Author Share Posted November 30, 2014 nice gauge, saves the headache of having too many gauges in the dash, if it a bit cheaper would consider it ! good job on the buildHave 4 other gauges aswell lol just need a new boost gauge And cheers it's come along way since I got it Quote Link to post Share on other sites
Glanza-Ben Posted December 4, 2014 Author Share Posted December 4, 2014 Finished stripping the glanza and as I was about to cut the dirty black brake lines I gave them a quick wipe the they were all earls braided lines Quote Link to post Share on other sites
Glanza-Ben Posted December 6, 2014 Author Share Posted December 6, 2014 when going to fit my gauges I realised my piller pod was 60mm luckily I found a swap for this center console which holds 3 52mm gauges so that's ideal for now Quote Link to post Share on other sites
amatthews45 Posted December 6, 2014 Share Posted December 6, 2014 Glad you like it dude! That's such a bad photo of my interior haha. Quote Link to post Share on other sites
Glanza-Ben Posted December 6, 2014 Author Share Posted December 6, 2014 Glad you like it dude! That's such a bad photo of my interior haha.Hahahahaha it's 100% better then my interior Quote Link to post Share on other sites
Calum122 Posted December 6, 2014 Share Posted December 6, 2014 Nice build. I like the engine build but what happened? Why didn't you use it? Was it because of that damage? Quote Link to post Share on other sites
Glanza-Ben Posted December 6, 2014 Author Share Posted December 6, 2014 (edited) Nice build. I like the engine build but what happened? Why didn't you use it? Was it because of that damage?Engine was sold on for extra funds this one is rebuilt aswell just needs painting which I need to sort and was easier at the time for me to lift out the motor and gearbox etc from one car and drop in the other Edited December 6, 2014 by Glanza-Ben Quote Link to post Share on other sites
amatthews45 Posted December 6, 2014 Share Posted December 6, 2014 Your making more progress than me Ben! I need to do a write up but just don't get on the PC often plus its to much of a state to put on here Quote Link to post Share on other sites
Glanza-Ben Posted December 6, 2014 Author Share Posted December 6, 2014 Your making more progress than me Ben! I need to do a write up but just don't get on the PC often plus its to much of a state to put on hereTomorrow should be a good day on updates, hoping to sort interior, fit the new brakes and possible rear axle swap but weather depending Quote Link to post Share on other sites
amatthews45 Posted December 6, 2014 Share Posted December 6, 2014 So jealous I should be wiring in my gauges Not like its any use with the engine all stripped down. Might try removed my window motors to see if I can repair them. Quote Link to post Share on other sites
Calum122 Posted December 6, 2014 Share Posted December 6, 2014 Nice. Yeah makes sense. Why didn't you save the Glanza, they seem to command more money than the GT's Quote Link to post Share on other sites
Glanza-Ben Posted December 6, 2014 Author Share Posted December 6, 2014 (edited) Nice. Yeah makes sense. Why didn't you save the Glanza, they seem to command more money than the GT'sWhy? Cause it was a piece of shit lol, wiring cut and bodged, shell rough, and bent chassis leg plus why save a glanza when I'm building a gt? Have had and stripped loads of glanzas in the past so wanted to do a gt Edited December 6, 2014 by Glanza-Ben Quote Link to post Share on other sites
Glanza-Ben Posted December 6, 2014 Author Share Posted December 6, 2014 So jealous I should be wiring in my gauges Not like its any use with the engine all stripped down. Might try removed my window motors to see if I can repair them.My windows did not work and found who ever stripped the shell unplugged a load of loom :/ Quote Link to post Share on other sites
amatthews45 Posted December 6, 2014 Share Posted December 6, 2014 Hmmm will have a look at my passenger one tommorow. My driver one judders but passenger one makes no noise. Good idea! The rest of the ac needs to come out as well. Quote Link to post Share on other sites
Glanza-Ben Posted December 7, 2014 Author Share Posted December 7, 2014 Started wiring this morning nd sorting the gauges out Now fitting the boost controller, turbo timer and stereo Quote Link to post Share on other sites
amatthews45 Posted December 7, 2014 Share Posted December 7, 2014 Looks good dude!! How do you rate that AFR gauge? Quote Link to post Share on other sites
Glanza-Ben Posted December 7, 2014 Author Share Posted December 7, 2014 Looks good dude!! How do you rate that AFR gauge?It's a narrowband gauge and not really it came in the car I stripped so.just wired it in for the more gauge look lol Quote Link to post Share on other sites
Glanza-Ben Posted December 7, 2014 Author Share Posted December 7, 2014 Radio and boost controller in Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.