Jump to content

Rob H@RCH Engineering

Member
 View Profile  See their activity

  • Content Count

    1683

  • Joined

  • Last visited

 Content Type 

Everything posted by Rob H@RCH Engineering

  1. Rob H@RCH Engineering
    Nice rite up mate is a long time since we crossed paths! Seen you a few times at pod over the years when I was last boosted last time I was at pod was 2005 lol
  2. Rob H@RCH Engineering
    The oil temps all depends on the shear point of the oil you are using different oils have different shear points it should all be in the tech spec of the oil or can be found on the net. I use gulf competition and thats good up to about 130c be for it starts to become less stable.
  3. Rob H@RCH Engineering
    BUMP
  4. Rob H@RCH Engineering
    BUMP
  5. Rob H@RCH Engineering
    BUMP
  6. Rob H@RCH Engineering
    Personally I think the teins are too hard for our shitty roads I used to run HAs on the rear of mine but I thought they where too hard so I am running the stock SR TTE suspension now and sticking with it as long as I can! But it's each to there own when it comes to suspension.
  7. Rob H@RCH Engineering
    Yep it will bolt straight on you just have to remove the plastic blanking plug on the front bolt hole on the front strut tops.
  8. Rob H@RCH Engineering
    herez mine
  9. Rob H@RCH Engineering
    Got mine cheers mate!!
  10. Rob H@RCH Engineering
    This is the glanza spoiler as you can see there are 2 holes on the pillar there for the locating clips for the spoiler legs and the top hole is for the bolt and the big hole is for the brake light wires. The SR boot has non of them I think, I never too my spoiler off I just changed the hole boot.
  11. Rob H@RCH Engineering
    It wont bolt straight on, as the glanza spoiler has extra bits riveted onto the boot lid for it to locate onto and holes for bolts at the top. you can drill and fit the extra mountings but make sure you get them in the wright place or it will be wonky lol. Or you can bond it on with out having to drill all the holes you will just need the one for the brake light wires.
  12. Rob H@RCH Engineering
    I could not say with out seeing the plug on the end of the harness and then it would be a bit of a guess.
  13. Rob H@RCH Engineering
    I a ep82 harness but its not a direct fit for this timer.
  14. Rob H@RCH Engineering
    BUMP
  15. Rob H@RCH Engineering
    BUMP
  16. Rob H@RCH Engineering
    Bump for the flywheel!!
  17. Rob H@RCH Engineering
    I was just looking at that lol can ya make it a white one please thats to see if I can rescue the old Peugeot lol
  18. Rob H@RCH Engineering
    Heres one we MOTed a couple of years ago bit classy I know!! and its a full 1.0l and the bloke that owns it is a copper lol its been sat on his drive for the last 10 years so he was getting shut of it I dont know what the out come was the lol
  19. Rob H@RCH Engineering
    I remember when this was all the rage!! back in the day of MAX Towers (max power) it was the in thing there was loads like that!! not my cup of tea tho!! One of the mates had a corsa with six working tail pipes not that big tho!! he was running over 400bhp on a red top too!
  20. Rob H@RCH Engineering
    Payment sent!!
  21. Rob H@RCH Engineering
    I will take one of each of Yellow, Green, Black, Black, Red, and a backing plate to match in 135mm please!
  22. Rob H@RCH Engineering
    Its the thread size I need to know my polisher takes a M14 pad I just need to know it will screw on. Cheers Rob
  23. Rob H@RCH Engineering
    What thread are the pads? I am going to have a set but need to know they will fit first lol
  24. Rob H@RCH Engineering
    That rain pick looks mad!! looking good mate.
  25. Rob H@RCH Engineering
    Pm sent!
×
×
  • Create New...