Taggy

I think the power envelope tails off a shit load after 1.0bar on the ct9, it starts blowing lots of hot air instead. I wouldnt run it a 1.2bar other than in scramble mode, for the odd race

Congrats dude!!

lol its a lonely existance on the ep70 leaderbord!

Ha ha mine had been on my car for about 4 years!! alot of grime and shit in them

welcome to hell with D2 coilovers, they are a complete nightmare to adjust once they have been on the car and rusted/covered in gunk. I had to take mine off completly and put them in a vice with a blow torch to heat them up and then whack the collars off. You can get them off just be patient, soak them in parafin over night or some other degreasant. If you want to raise or lower your car never adjust it by the spring, always do it by the collar at the bottom and wind if up or down on the thread as required. If you adjust the preload on the spring it will just cock your suspension up and ruin your ride There are two collars to undo if i remember right, one on the top and the bottom and then you just rotate the whole purple thing around on the thread, you need loads of WD40 in there! Here is mine soaking over night Good luck!!

thanks!!!

when you rotate it you undo both sides of the turbo, this way you can turn the oil dran so it points downwrds (this is a must) and then rotate your compressor housing to what ever direction is best to connect to your intercooler piping. I bought some extra fittings from viperperformance and reused my ct9 fmic was a bit fildy but it worked a treat

how much did the godziller turbo kit cost?

yeah done that about 3 times now stil bloody rusty!!

My old track car had a shoddy rusty radiator which i replaced with a nice aluminium one, but the rust which was in the engine system still, has contaminated the new radiator and no matter how many times i fush it its always REALLY rusty, so rusty in fact you look inside the pipes and rad and its all completly orange. What can i put in my radiator system to eat away all this excess rust? its driing me crazy!

Bit of an update, engine is all back together now with the gearbox, i just finished it Also gave it a spray too to spruce it up a bit Next is sorting out an engine crane to put it in, - Nearly there!! I am a bit miffed i cant make japfest 2 with it as I still have quite a bit of work to do even when its in the car, but at least its progress!

Hey John, yeah i pulled it apart the other day and resealed the bloody thing. Bit of a pain in the arse but its done now Still cant believe i missed that, its not documented very clearly in the manaul and missed it. So the engine is all built ready to go, next was onto my gearbox! It had been jumping out of 5th gear so I needed to fix that before i put the box back on. This again has been a royal pain in my ass. Mainly down to me buying shit tools from ebay!! I needed a gear puller to get the 5th gear off and the one i bought stripped its own thread when i did it up, so i was like argggghhhhh!!!! Anyhow thats now sorted with a new puller and the gearbox is back together, I just need to fill it up with oil and stick it onto the engine. Then its clean the engine bay up time with some GUNK and drop the engine in time So i am not far off now!!

fuck me that actually just made me say "holy fuck in front of the my mother lol!! oops

Yeah you will whoop him easy, here is me in my td04 1 bar in the ep70 racing the rx8. I wasnt even giving it full beans because my suspension was rubbing so bad on the corners. I drag raced him later in the week and whooped him easy off the lights, did struggle a bit to get the power down though! http://www.youtube.c...bed/u8Umni6UNd0 http://www.youtube.c...bed/phh27J_Ed6Y

The piston bores will be super smooth, its called "glazed" they are not supposed to be rough on an engine which is run in. You would only ever have a rough surface when the bore has been cross hatched and honed ready to accept new piston rings. If they were not smooth when running normally your engine wouldnt be able to make a good seal with the piston rings.

did he go bust or somthing and tuck a load of members up while he was at it?

Hey Morgey, repairing the 5th gear jump out syndrome is actually a fairly simple job. You can do it on the car without having to remove the gearbox i would imagine also too.

haha a bit of searching and i found this little gem, problem solved! http://www.imoc.co.uk/forums/kb.php?mode=article&k=100

cheers glanzagee that would be a great help!

My 5th gear is currently popping out all the time, i have taken the gearbox cover off showing off the 5th gear asembly. I have another gearbox which i am just going to do a straight swap with the 5th gears. I dont want to go damaging anything as I know you have to pull off the 5th gear with a puller. Although I am not 100% on the process for this can someone explain what i should do to take them off so i can swap them out. Currently it looks like this (i havent taken the big nut off which is normally on the left) I have a replacement 5th gear, how do i remove it do get it like this! Can someone explain to me what i need to do, including giving me a link on which puller you think i should get. I have got a gear puller already similar to this, can i use this? Which part of the gear should i place the puller on?? Does it all come off in one go etc? Any help would be great Craig

Ok look like i can change over the 5th gear without to much trouble, i dont even need to open up the box, only just the end cover! Just found a brilliant write up on taking apart and rebuilding the C52 gearbox :@ http://www.ae92gts.com/ae92gts_trans_rb_1.html

Yeah I have been whacking and whacking on it all day and night and not even a press has had any luck, maybe if i whack it the other way to try and free it up like you said (off i go to the shed!) Does anyone know how to change a 5th gear selector also?

well at least i didnt fit it into the car and then realise i had dont that!!

Its really doing my head in, i have been trying for 2 days to get it out and it just wont budge. The only thing i can think is that somehow the circlip has come of the end and has somehow jammed its self in the spline, arggghhh! somthing that should have taken 10 mins is now turning into a right ball ache