PaulStarletSR Posted September 6, 2013 Share Posted September 6, 2013 put on the new inlet/tb and it fixed the problem for 2seconds then back to the fuckin huntin idle! any fresh ideas? am goin mad here!! Quote Link to post Share on other sites
TrisK Posted September 6, 2013 Share Posted September 6, 2013 Unplug the Ecu for a bitIt might have adjusted the mixture to compensate for the vacuum leak Quote Link to post Share on other sites
PaulStarletSR Posted September 6, 2013 Author Share Posted September 6, 2013 aye but when i cover the TB again it DOESNT CUT OUT.......LEAK!!!! where the fuck is it???????? Quote Link to post Share on other sites
mikey4410 Posted September 6, 2013 Share Posted September 6, 2013 noooo,fucking hell Quote Link to post Share on other sites
Chris Green Posted September 6, 2013 Share Posted September 6, 2013 What is the head like, is the surface where the manifold mates to the head smooth? Quote Link to post Share on other sites
PaulStarletSR Posted September 6, 2013 Author Share Posted September 6, 2013 its all good! new gasket from iddy aswell! im so close to explodin! why oh fuckin why will this not just fuckin run ryt!!!!! Quote Link to post Share on other sites
Dan_Henderson Posted September 6, 2013 Share Posted September 6, 2013 Cracked head? Quote Link to post Share on other sites
Chris Green Posted September 6, 2013 Share Posted September 6, 2013 I used sealant on the head and manifold too, just to be on the safe side. Quote Link to post Share on other sites
morgey Posted September 6, 2013 Share Posted September 6, 2013 shoulda gone 4age, much less hassle Quote Link to post Share on other sites
ryan lang Posted September 6, 2013 Share Posted September 6, 2013 Told you it would have had the same problem! You need me ill come fix it Quote Link to post Share on other sites
PaulStarletSR Posted September 6, 2013 Author Share Posted September 6, 2013 no cracked head, its fine. all fresh. what else could it be to be still runnin when i block the TB?? its bustin my balls Quote Link to post Share on other sites
Dan_Henderson Posted September 6, 2013 Share Posted September 6, 2013 Block the throttle body and spray some of the areas with carb cleaner and when the car idles higher that's where it's leaking from Quote Link to post Share on other sites
Chris Green Posted September 6, 2013 Share Posted September 6, 2013 I would block absolutely everything bar the feed for the MAP sensor and have a check. Quote Link to post Share on other sites
PaulStarletSR Posted September 6, 2013 Author Share Posted September 6, 2013 gona get carb cleaner 2moz and block the TB and start sprayin the vacs etc and hope for the best. i just really really wna hav the first drive in her now because i know shes a fuckin weapon and i cany drive her til this is sorted! Quote Link to post Share on other sites
rinseep82 Posted September 6, 2013 Share Posted September 6, 2013 I have air leak tester at work mate ill send u a bottle fuck carb cleaner this shit is awesome stuff use it for testing manifold leaks on entinox cylinders at the hostpital spray some of that about you will find it if there is a leak Quote Link to post Share on other sites
PaulStarletSR Posted September 6, 2013 Author Share Posted September 6, 2013 I have air leak tester at work mate ill send u a bottle fuck carb cleaner this shit is awesome stuff use it for testing manifold leaks on entinox cylinders at the hostpital spray some of that about you will find it if there is a leak how does that shit work then mate? same principle.....spray on vac hoses etc while engine is runnin? Quote Link to post Share on other sites
rasslenny Posted September 6, 2013 Share Posted September 6, 2013 could be the idle screw mine was leaking through that a few days ago Quote Link to post Share on other sites
PaulStarletSR Posted September 6, 2013 Author Share Posted September 6, 2013 could be the idle screw mine was leaking through that a few days ago defo not that either Quote Link to post Share on other sites
turbo Grant Posted September 6, 2013 Share Posted September 6, 2013 Are your injectors nice and secure? But have youTry disconnecting all the vac lines post of the throttle flap, bar your map and frp. Blank the rest up. Even blank the pipe off that comes off the idle up valve on the end of the manifold. You need to sort it! Or get a smoke machine and stick that in the intake. Quote Link to post Share on other sites
PaulStarletSR Posted September 6, 2013 Author Share Posted September 6, 2013 injectors r spot on mate. im tryin to get my pal down from his at sum point on sunday/monday as hes a mechanic n reckons hel find the problem but until then il get carb cleaner and do that check, also do the others aswell Quote Link to post Share on other sites
rinseep82 Posted September 7, 2013 Share Posted September 7, 2013 Yea mate spray on anything u think is leaking and it turns all bubbly like a thin foam you can see it right away Quote Link to post Share on other sites
yaristurbo Posted September 7, 2013 Share Posted September 7, 2013 meet at pauls house fetch your diag equipment lol Quote Link to post Share on other sites
rinseep82 Posted September 7, 2013 Share Posted September 7, 2013 Where you live dude??? Quote Link to post Share on other sites
rinseep82 Posted September 7, 2013 Share Posted September 7, 2013 Quote Link to post Share on other sites
Beastmode panda Posted September 7, 2013 Share Posted September 7, 2013 Is EVERYTHING plugged back onto the inlet mani, I mean ALL vacuum pipes? How tight is the throttle cable? If it's too tight and it's holding the butterfly open even a little bit then air will be passing through it. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.