lukEp

Glad you got it mate and sweet on the coilies I need a set my rear shocks are bust

Wasn't me!

Mine Does look pritty standard ATM

Might of been me..... Standard alloys and black rear lip?

Cheers guys thanks... Yeh injectors looked horrid so give them a quick rub with 400 wet and dry and VHT paint! All new injector seals rob (£50 form toyota 12 of them) so hopefully no leakage Not any more pictures yet all the bits pictured are spares so the car can still be used I'll defo update as I go along

yes carbon parts are lush another part has started to...... Engine bay clean up! smoothed rocker started, clean injectors and fuel rail, inlet mani and TB plus do something with the exhaust mani heat sheild, lots of heat wrap for exhaust and inlet pipes plus going to overhaul all my calipers and replace fluid with dot 5.1 as one is sticking on slightly still need to fit ALK which ive had for ages now and now i've broken my AC pipe to the pump and even though I have a replacment pipe for now the pump and rad will be coming off till I sort out an alterative route for the intake. few pictures oh yeh oil pressure guage

How the hell did I forget about this sorry lads, I never even seen dan's post lol I'll send you a PM Lee

Yep all paid have been posted now Plus the extra ones you asked for

Lol first 5 have gone now so it'll be £11 posted paypal is de-cals@virginmedia.com. PM me your address and what colour TRD decal you want

When I have the dials and done I'll start a new thread for the GT

go into post office dude they will sort it

the glass is the same but the motor/wind mech will be different for obvious reasons ;)

mines flaking after respray at the bottom of rear qarter glass ;) yet again more awesome work mate

that looks fucking sex!!!!!!!!

No defo not selling mine mate but I will text Jason now and see if he will make some more as a few people have asked me about them, if there's enough I'm sure he will do another batch.

Carbon Dial Decal fitting guide 1. remove the clock cover by removing the two screws under the top as in the picture. and pull the top forward then pull it out. 2. you will of then exposed the clocks, remove the three screws 3 once there removed you will have access to the tobs to remove the surround without removing the whole clocks you need to unclip the 6 tabs here to get this 4. remove the clear plastic off the front (8 tabs) 4 top 4 bottom 5. Peel the sticker off the backing and spray with a little window cleaner (this is so you can adjust it in you havent sat it right first time. 6. place the sticker over the dials try and get it as square as possible and drop it into place adjust if nessasery 7. leave to dry and run your finger over the decal to make sure its all stook down 8 apply the trd decal 9. put the clear plastic back on the surround and wipe off any finger prints with a soft cloth 10. fit it back on making sure to be careful of the millage reset button in alligned correcly 11. replace the three screws holding the clocks in 12. replace cover and two retaining screw Admire! Takes 10-15mins cheers Tom (lad in the picture)

Lew I'm now getting them in the morning might take a few days to get the dials ready for scanning then a few hours to tart up the vector and get it the right size

1 comment....... AWESOME! How does it drive with them wheels then?

PM'd

I already have the blue available but it's at the higher price of £16 due to the price of the material being alot more expensive And the stainless dial are off Jason_l off here but he only had 4 sets made and there's all sold so there a very limited edition.

Welcome mate

That's bad news mate, seem to be more stories like this lately.

Pictures you slag

Just in levinstone but heading back to Manchester in half hour

If only I was coming up in my v but I'm not maybe next time.