Akyakapotter's Forged Glanza V

[akyakapotter]

well here she is she started with blitz nurspec r cat back exhaust blitz turbo timer jam fcc jam actuator and racing hart alloys

had a few problems with her over boosting when i picked her up got sent down to plymouth to be put on a rolling road to find out what she was doing it was over boosting this is the out come dyno read out.

they ended up putting a bung in to stop her boosting so much temp fix

next on the list was a decat and mani havent got a pic of the mani yet though

the next thing was to fit my front mount

next on the list is to lower her coil overs me thinks want it this low was with a full car going to work at a festival

have a Sard RRFPR to fit when i get the adapter for the fuel rail

 

[akyakapotter]

shes now sat how i want her to be on new rear shocks and tein springs much better to drive

Edited July 7, 2017 by akyakapotter

[Lukew360]

Looking good mate

That hole that was left open on the inlet pipe really should of been blocked, anything could have got sucked through your turbo/engine

[ryan33hks]

Sits much better now, standard ride height is shocking

[akyakapotter]

Wasn't left open mate was just to show the restriction I had in it to stop my elm till I hot my sard on there :-) I know they ate 4x4's standard hight lol

[akyakapotter]

Polybushed the engine the other weekend also got an ajustable pinhard rod Rear anti roll bar and a TD04 turbo going to be a busy boy over the coming months also dipped in and got some new tyres uniroyal Rainsport 2's

up on the ramp :-D

the underneath cleaner than what i thought it would be

Front gear box mount polybushed

Rear gear box mout polybushed

Front engine mount polybushed

engine being held up

TD04 :-D

my new tyres Rainsport 2's

Edited July 7, 2017 by akyakapotter

[lew777]

looks mint dude

[akyakapotter]

thanks fella it is mint apart from a nice scratch on the drivers wing and bumper (my fault) dam garage door lol cant wait to go TD04 :-)

[LukeSR]

Love Whites Glanza's

[Jamie1st]

Looks good man, keep up the good work!

[Amjad]

Those tyres FTW

Looks lovely

[templar2007]

Lookin nice mate looks like your goin to be busy soon

[akyakapotter]

i am mate love getting the spanners out also got the task of finding some one to give me a sympathetic mot with the TD04 0n :-)

[Burny]

good work mate :-)

[ro55ifumi]

Some nice work going on

John

[Glanza Mac]

Looking good dude

[akyakapotter]

cheers fella ive got lazy ive got a rear arb and panhard rod to go on had then about 2months need to pull my finger out lol :-D

[Glanza Mac]

tut tut, get them fitted

[akyakapotter]

ok so a little up date i got round to fitting my whiteline rear arb on friday and my god my car feels compeatly different. I love it by far my best mod to date comment welcome as always :-D

[206wasstarletpower]

I am very tempted by one of these. Did you find the cars rear end a bit loose under braking before fitting these??? If so i might have to purchase one myself

[akyakapotter]

before i had put it on it used to feel like it wanted to step out alot i drove to work this morning in the wet around a very sharp bend at 75mph before i wouldnt have even thought about going fast as id have shit my pants but with the rear arb it was so smooth i love it i highly recomend one mate well worth the money in my opion

[Liam_D]

Whiteline RARB's FTW!

[*Zoe*]

Nice build you have going here

[akyakapotter]

I spend far to much money on it lol. got a japspeed decat on the way won it for £21 a new lambda for a tidy sum of £11 a depo wideband and looking at a gizzmo boost controller and shortend hot pipe off dean. The TD04 can wait till after the summer.

[akyakapotter]

look what just come in the post my eBay bargin one brand new Japspeed Decat for the tidy sum of £29.96 delivered. Will be fitting it after i get my M.O.T done in a few weeks