Jamie5414

Really good write up Rbz I have to agree with Zeldoz though, The welds could be better, especially around the pipes, to finish it off. http://i.imgur.com/iVto3Ab.jpg

32mm grommet will fit flush

Sorry ,It is the 4EFE Inlet, Like Tobz suggested, I just double checked and it's the same as one I have in my garage. There are a few N/A Starlets being broke on here for parts, Here is one, he might have the TB http://www.ukstarletowners.com/topic/75936-toyota-starlet-na-for-breaking/

Glanza Inlet, So the Glanza TB will bolt straight onto it

Me too, down there most weekends Can't attend japfest this year though last one I went to was 2011 haven't been since

PM Mickey Boy here, I managed to get some of another member but he said he had some., http://www.ukstarletowners.com/topic/75936-toyota-starlet-na-for-breaking/

Yep crank is the same between 4efe and 4efte

Yes that's a four piece, I didn't know ID workz did them to be fair I'll take a look on their website now bud cheers for letting me know.

Don't use Waxoyl buddy, It just hardens and flakes off after a while (Which is what is happening it me now), Stone chip it then paint over that, and clean the arches down often, that's the best thing to do.

Sorted

You can import a picture bigger then 1mb iirc, you don't have to select it from your computer

Sweet mate, pm me your paypal and how much postage is and i'll transfer it for ya

I'm after two double filament Bulb Holders for the rear lights. Need to have the cables sticking out of them, as long as possible. (These are the two top holders on each of the lights & break light) Do you have them mate? PM me

I'm after two double filament Bulb Holders for the rear lights. Need to have the cables sticking out of them, as long as possible. (These are the two top holders on each of the lights & break light) Do you have them mate? PM me

Hi, I'm after two double filament Bulb Holders for a rear light on a ep91. Need to have the cables sticking out of them, as long as possible. Jamie

Opie oil's said that the best oil to get is the Fuchs Titan Race Pro S 5w-40 Fully Snyth

Sweeeeeeet Glad you got it running mate, need a video of you giving it some now

Just ordered some of these http://www.ebay.co.uk/itm/370536739702?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649 and some Motul RBF600

What was the guys name you hit on the bike? TBH your real life issues don't change the fact your a scammer, scammer's should be banned from logging on here.

So I thought i'd write it up, couldn't find it anywhere.... 98 Spec/Reflet Side light mod Before: After: Pins that I will refer to in this guide: You will need 2x Double Filament Bulb Holders (A breaker may have them in The Marketplace) ***Get a holder with wires sticking out as long as you can get, so you can solder onto them, otherwise it'll be a nightmare taking the holder to pieces to solder in wires. *** 2x Double Filament Bulb Wire (Two different colours: Green and White&Black (or just White)) Side Cutters Soldering Iron Solder Small Heat shrink (3mm) Heat Gun Cut the wires of the _bottom_ holders on each light and put them aside (Leave a bit of cable on the holder so you can always revert back and use the same holders). PASSENGER SIDE: Cut the Green wire on top holder, splice in a new Green wire and leave enough length to go to the bottom holder. Cut the White&Black wire on top holder, splice in a new White&Black wire and leave enough length to go to the bottom holder. Solder the new Green wire onto the "top pin" (Or the cable going to one, if you bought the holder with cables sticking out). Solder the new White&Black wire onto the "negative pin" (Or the cable going to it, if you bought the holder with cables sticking out). Solder the old (Reverse) Blue wire onto the "center pin" (Or the cable going to one, if you bought the holder with cables sticking out). DRIVERS SIDE: Cut the Green wire on top holder, splice in a new Green wire and leave enough length to go to the bottom holder. Cut the White&Black wire on top holder, splice in a new White&Black wire and leave enough length to go to the bottom holder. Solder the new Green wire onto the "top pin" (Or the cable going to one, if you bought the holder with cables sticking out). Solder the new White&Black wire onto the "negative pin" (Or the cable going to it, if you bought the holder with cables sticking out). Solder the old (Fog) Light Green wire onto the "center pin" (Or the cable going to it, if you bought the holder with cables sticking out). Insert double filament bulbs into each holder and insert into the light. Turn on JDMness! Jamie

PM Keri, There was a group buy just past for rough pricing (Ignore the price match later in the thread) http://www.ukstarletowners.com/topic/72471-discspads-for-toyota-calipers-inc-wms-110-heavy-duty/

Money waiting!

Aberdeen mate, not far, a few members a bit south of where your at on here

Welcome Bud, Where abouts you from in Scotland?

hahahahaha