WallaceGlanza

I've got the pair mate. Can either meet up again or just cover the postage.

Sacrilege putting rays stickers on fakes!

Bump, still some bits left....

Glad the seats are going to a good home.... your arse will love them!

I've got good rear calipers off my glanza, rebuilt them completely a couple of years ago (and have only done a few thousand miles since then).

Got a pair of these as well mate...

Could also be the rear gearbox to engine bolt...tbh there's a lot of bolts it could be!!

Would do them both £60 plus postage, I can either stick them on a pallet or just cardboard wrap them and let you arrange postage - then you have the option for insurance etc

I've got a road runner mild steel manifold, stock fitment. See the breakers section for a photo.

Bonnet is generally very good with minor stone chips. The back corners were both damaged when it was posted to me, I smoothed these back and touched up they just don't come to a point like they should: The crack is down the passenger side edge, it could be filled and re-painted easily but id barely visible when the bonnet is down:

Wings are in good condition, some stone chips and a couple of small scuffs barely visible, the drivers side has a slight rust bubble on the lip which was touched up but has come back. Both sides are also a bit rusty right at the bottom but the sideskirts cover this area: This one looks a lot worse in the photo!!:

Provisionally sold mate, will let you know if they don't go though. Would rather sell the whole rear brake assemblies complete. Replied and also replied to your last two pm's.... Sorrry Liam I'd really rather not, it got damaged last time and is very fragile! I know! I must admit to getting a bit emotional ripping it apart today!

I've got one.

Nope. They are line bored together so would need re-done if swapped...and then the can shaft probably wouldn't fit.

Yeah could easily meet you. It is 100% genuine,shorty on here had it imported himself before the replicas came out. I'll get some photos for you tomorrow but its not bad.

Angus,Scotland. Willing to travel with it too within reason as really don't want to post the bonnet.

Ok. Once I have them off will let you know and take it from there I know but needs must Yup, they will both be available, I'll some photos once they're off.

The clutch is awesome, glad you're happy with it, you'll get used to the race car noise! I did mention in the advert that the lower arm bar was scratched and dented - any used one will be since they're so low on the car, watch out for rabbits and speed bumps with it! ;)

That's an airbag!

Now breaking See here: http://www.ukstarletowners.com/topic/90817-breaking-black-glanza-with-mods/ Mods this can be locked please.

Finally decided to break my glanza so everything on it will be available, most parts will be removed tomorrow. I'll get photos of all parts as required. Prices are fair and firm, I don't have time to have long conversations with people who can't pay until their granny's inheritance gets delivered so if you want the parts you need to have the cash. Everything is sold as seen but all working properly when removed. Item's & Pricing For Sale: Stock glanza 4efte fully rebuilt 1500mile ago - (SOLD) Standard GT gearbox, low mileage 73k, No crunches. - (SOLD) Solid brass shifter cable bushes (pair) - £15 XS Power Front Mounted Intercooler kit with short pipe route to suit CT9, no bumper cutting required - £80 Apexi Filter Induction and Relocation Kit to suit CT9, relocates filter to front grill - (SOLD) Standard CT9 and standard actuator (Refurbished unit by midlands turbo done approx 40k miles) - £80 HKS Actuator - (SOLD) Road Runner CT9 Exhaust Manifold - (SOLD) Blitz Decat and lambda - £120 Custom Straight Through Stainless 2.5” Exhaust with Trust Power Extreme II Back Box Fully Heat Wrapped - (SOLD) NGK Blue Leads -£30 Walbro 255lph Fuel Pump (Complete assembly ready to fit) - (SOLD) SARD RRFPR c/w gauge, fuel rail adaptor and hoses (Original box and instructions too)- (SOLD) SARD R2D2 Dump Valve - (SOLD) 40mm thick Aluminium Radiator with Pacet Fan - (SOLD) GReddy Emanage Blue with ignition and injector harness and custom carbon fascia for centre console - (SOLD) Blue earthing kit - (SOLD) Custom catch can (proper demister pad inside and 3rd port) with silicone hoses (fluoro lined) - (SOLD) Drivetrain: TC Short Shift Kit (full assembly)- (SOLD) Exedy Clutch kit (Brand new standard jobbie, done 100 miles!) - (SOLD) Chassis: MeisterR Zeta R Coilovers -(SOLD) Whiteline Anti-lift Kit -(SOLD) Whiteline Pan-Hard Rod (seized!) - £40 Poly Bushed ARB Drop Links (Brand new done 100 miles) - (SOLD) Powerflex Poly Rear Axle Bushes - (SOLD) Powerflex Poly Engine Mounts (Full units ready to bolt in, edge of gearbox bush slightly melted) - £80 Earl's Braided Brake Lines full kit (x4) replaces both rear hoses - £50 ABS Removal kit (Hard pipe kit) - (SOLD) 10mm Wheel Spacers - £20 Interior: Evo 7 Recaro Seats, very good condition will bolt straight into an EP91 -(SOLD) Pioneer DEH-P6750MP Headunit and Pioneer TS-E1076 front speakers - £80 Exterior: Genuine Cruise Power FRP Bonnet with Locking Aerocatches (Slight crack down one side and some stone chips) - £300 ‘98/’99 Front Bumper with genuine OEM splitter smoothed in and foglights, grill and brackets to bolt straight onto a 96/97 EP91- (SOLD) ‘98/’99 Clear Front Indicators and proper housing, comes with silvatec bulbs - (SOLD) JDM Reflet Rear Light Clusters, full units with bulbs - (SOLD) Those are just the mods but everything on the car will be available when removed. Pictures: Payment & Shipping Details: To be arranged with buyer, buyer pays any fees. Smaller items can be posted. Parts can be collected from Angus, Scotland

I've got a custom 2.5" system with trust back box and a road runner ct9 manifold, just removed.

Bump

Bump

The thermostat housing studs are very soft but mole grips should easily get the snapped stud out,they did with mine.