Simon

Which controller will it need mate 1 or 2?

they fit both

What else does the EGT gauge need to run mate?

As there has been a few instances of fake mapped ECU come up i thought i would share these pictures. I brought a starlet that i knew had been modified in Japan there were no external fuel modifications that i could spot and this is how the ECU looked: Looks standard enough no stickers or seals but i was sure there was something done to the ECU so i opened it up: Here you can clearly see the daughter board that has been fitted to alow the use of a chip that can be written to form the specific map on that car. As far as i'm aware nobody has managed to connect to a stock toyota ecu and rewri

Rota's are a direct copy of another companys work though. The Japanese manufactures spend a lot of money on coming up with these designs and also the majority of the wheels they produce are forged and not cast this makes the wheels stronger and lighter than a cast wheel but this is only really needed and wanted for people that want the best of the best for racing most OEM wheels are cast. Rota are offering a copy that is not of the same specification as the wheel they have copied but they still meet the JWL standards so are fine to use. They are one of the biggest manfactures of OEM wheels in

But every Rota design is a direct copy of a JDM wheel

Other than for an all out track car i can't really see the point in the FRP doors and boot and if i was building an all out track car it wouldn't be a starlet. With all the copied stuff about the only rare parts are the Tom's EP91 stuff (apart from the front bumper) and the cruise front bumper oh and the varis rear spoiler

Has it been ended because soemone has made the seller a cash offer though? Guess only time will tell, will have to see if a "I've just brought a wedsport ecu" thread turns up.

Zep tended to use a sard wing on custom mounts there was one on the auctions the other month. Thats what the blue car used.

They sold for a insane 25,000 yen which is nearly £200 To add to that you would have a buyers fee, internal postage within Japan, auction fee and then postage to you from Japan.

Ask him for some photos of inside the ecu will soon be able to tell if it has been altered then. All he has got to do is take the lid off.

http://www.archenemy.co.uk/

I always use: http://www.willtheyfit.com/ As you can play with tyre sizes too

I think you would struggle to do this for any real benifit as you would really only be doing this for looks which i would guess would mean a low offset wheel. Considering most people struggle with an 8J ET10 a 9J wheel would have to be ET20-35 and will still need quite a bit of work and will always be a compromise.

Since i sold my ignition barrel light a few people have asked me for a wiring diagram. There are 3 wires to these lights: black - earth earth to the body Red/silver with a white stripe Red/silver These are wired in on a Glanza behind the pannel below the steering wheel. If you remove the air ducting you will find acess easier. On the right clipped to the body you will find a plug like this: The red/silver wire goes to this red wire in the above picture (please note the location not the wire colour as it looks like my car has a small extension harness between the plugs guess this is how toyo

Just set up a bib jdm account and get them mate all you need is paypal

http://ord.yahoo.co.jp/o/auction/SIG=12bhhsr98/EXP=1352484495;_ylt=A3JvdVgP9ZtQqmYAWLNAPDh8/*-http%3A//page8.auctions.yahoo.co.jp/jp/auction/h170149765

I take it you have the cruise ones from the cruise web site? Thats the only only place i've seen them on.

Rob that was a members car on here. Ian i think his name was i went over there to collect some parts him i reconise the place.

Matt HRF didn't make a rear bumper only the spats. This is a winning sports rear spoiler: http://i2.photobucket.com/albums/y44/SiCaln/Parts/ep91/WinningSports/WS98lip.jpg

What i need is just the end that goes through the wheel bearing i want this to put in while i wheel my car about when it's having some work done. Also i want the bar that support the bonnet catch run from the bottom up to the top support bar think people remove these whan fitting big coolers so might be a few about.

Whats your thoughts on the EP91 rear torsion brace Mike do you think it will do much? Doesn't seem to go to the bolts that holh the rear axle in.

A 98 spec splitter would cover a lot of that up

http://page7.auction...tion/g114900242 I was used in the late EP82. Mixed flow turbine RHF5 Anchiragu ECU (SS crazy) Boost controller (Blitz DUAL-SBCSpecR) Fuel regulator (adjustable NISMO) Fuel pump (genuine CT9A Lancer) Injector (JZS100 genuine Tourer V) There is no pump and an injector in the picture (and I included. The above is a set. The engine body is also genuine exhaust manifold in the normal, straight 70 pi, and the muffler intercooler was using genuine CN9A. It was used in boost 160Ps Dynapac 1.6. Since additional ECU is the foundation have Teku align with the curre

Depends on the down pipe if it's on a stock cat, blitz de cat then thats what they use some others do also depends on if there is the recess for ir in the down pipe.