TrisK

how bad is it? and where is it? although mx5nutz were there in 2013, and they have cars that are a lot lower than ours!

ive almost got everything i need to do mine shaun. so ill be intersted to have a feel of yours ;)

Flint has some volks matt

I'd check general timing

Which one you brining this time chap?

shaun, remind me how you made the low pressure line? is it just a cut and jubilee job?

I tried the cut outs last night, and i get contact with the cut outs. are you sure that you made sure they were 1:1 by measuring the lines they tell you to measure. Cheers for that Aamir, that is helpful. I reckon that if the cardboard cut outs are correct then i could get away with a 3-5mm spacer. but the problem is i couldnt run more than that. and i dont really want to change my wheels just yet, also i dont particuarly want my wheel choice to be denoted by my brakes Its a tough one. If i could do it with a 3mm spacer or so I would

Just tried my templates. It's close on all set ups. Anyone have experience is size and spacer combos? They are 15s

Those wheels are beautiful. Would love a set. I had a set of te37s and they were very very light. What are the v's like? Much heavier with the dish?

Definately save it. 98 spec bumpers might even be discontinued now if i remember right...

Could you not save that bumper with some heat a gentle persuasion?

Ha.

Try the driftworks ones mate Zero play and you can wire the horn though

Can you still buy ep82 Indictators lenses? I had one brake in the post

Just milking the snap off boss. Was a meet that was mainly porsches and more expsnive cars, so we all rocked up in modded jap stuff and milked it. was fairly amusing. Confused an awful lot of them Yeah its nice a bit closer, took a bit of getting used to though, and its a bit annoying that i cant reach the inidicators as easily, but ive got used to it Really impressed with the driftworks boss though, no play at all, and a really nice release and relocation felt a lot of ebay ones in other cars, that you dont feel like the wheel is really attached

i need to add a big thanks for Flint for helping me take my glow pannel off. otherwise it would have ended up in 3 peieces. Toyota dont half put some clips in stupid places. You end up working blind or there isnt enough room to get pliers in to release the clips. But with flints help it came off and went back on with no damage. Cheers bro

I wrote a big long post, but i accidently closed the window So here is a summary I pretended to be a post van: I polished and remade my glow badge from vinyl Thanks to my mate will for polishing help and Starbuck for the design Before and after: My mate josh made me some genuine carbon fibre number plates My mate cal took a photo of the car really clean:

dodo juice wax

I came to the conclusion thy they didn't make a recaro rail either. Mine from Japan had a bride rail with two adopter plates I'd go with the universal rail. You literally just bolt the feet from the standard rail on and it is a genuine recaro rail. Just a universal one

You arent anybody without 15x8 et0 bro The rotas come in 15x8 et0.

Bump

Message turbogrant. He has a garage and does custom work

I did read something about a putting a td04 hybrid wheel into a tf035 housing. Or a td04 rear onto a tf035. Ill try and find the link

>https://www.youtube.com/watch?v=8DATpqSk3W0 Try this Charlotte. Thats the noise

Yeah, its a reminder in Japan.100kmph is the max speed on the expressway. So it goes off just over that to remind you that you are speeding. Pointless and probably really annoying over here. But I can deal with annoying for extra JDM option-ness, and the ability to tell a story. Plus we drove from Leeds to Poole in my mates AE86 with the bell going and it really wasnt that annoying